Country Flame DV 46 Manual De Usuario
OPERATING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:
If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury, or loss of life.
A.
The Bayvue DV has a pilot light system that must be lit by hand.
Follow these instructions exactly, when lighting the pilot.
Follow these instructions exactly, when lighting the pilot.
B.
BEFORE LIGHTING the pilot light, it is important to smell all around
the Bayvue DV for potential gas leaks. Be sure to smell next to the
floor because some gas fuel is heavier than air and will settle to the
lowest point.
WHAT TO DO IF YOU SMELL GAS
the Bayvue DV for potential gas leaks. Be sure to smell next to the
floor because some gas fuel is heavier than air and will settle to the
lowest point.
WHAT TO DO IF YOU SMELL GAS
C.
Use hand pressure to push in or turn the
ON/PILOT/OFF control knob. Do not use a
tool. If the control knob will not push in or
turn by hand, do not attempt repair. Call a
qualified service technician. Attempted repair
may result in fire or explosion.
ON/PILOT/OFF control knob. Do not use a
tool. If the control knob will not push in or
turn by hand, do not attempt repair. Call a
qualified service technician. Attempted repair
may result in fire or explosion.
• Do not try to light the Bayvue DV.
• Do not touch any electrical switch; do not use any phone in your
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
D.
Do not use the Bayvue DV if any part has
been under water. Immediately call a
qualified service technician to inspect the
Bayvue DV and replace any part of the
control system and any gas control that has
been under water.
been under water. Immediately call a
qualified service technician to inspect the
Bayvue DV and replace any part of the
control system and any gas control that has
been under water.
LIGHTING INSTRUCTIONS
1.
STOP!
Read the safety information above this section.
8.
Push in and turn the ON/PILOT/OFF control
knob counterclockwise to “ON.”
knob counterclockwise to “ON.”
2.
3.
4.
5.
6.
7.
6.
7.
Turn off all electrical power to the Bayvue DV.
Open the Bayvue DV bottom panel to expose the gas control panel.
Push in on the ON/PILOT/OFF control knob slightly and turn
clockwise to “OFF.”
Wait five minutes to clear out any gas. Then smell for gas including
near the floor. If you smell gas, STOP! Follow “B” of the safety
information above.
Turn ON/PILOT/OFF control knob counterclockwise to “PILOT.”
Push in the ON/PILOT/OFF control knob and hold in. By repeatedly
pressing the piezoelectric igniter, a pilot flame should appear. If
flame goes out repeat steps 5 thru 10. If flame stays lit, go to Step 10.
Open the Bayvue DV bottom panel to expose the gas control panel.
Push in on the ON/PILOT/OFF control knob slightly and turn
clockwise to “OFF.”
Wait five minutes to clear out any gas. Then smell for gas including
near the floor. If you smell gas, STOP! Follow “B” of the safety
information above.
Turn ON/PILOT/OFF control knob counterclockwise to “PILOT.”
Push in the ON/PILOT/OFF control knob and hold in. By repeatedly
pressing the piezoelectric igniter, a pilot flame should appear. If
flame goes out repeat steps 5 thru 10. If flame stays lit, go to Step 10.
9.
10.
11.
11.
Close the Bayvue DV bottom access panel.
Turn on electrical power to Bayvue DV.
The pilot flame should be visible through the
door glass in the lower right hand corner
between the front and middle logs. See the
picture below for parts description and view
of normal pilot flame pattern.
Turn on electrical power to Bayvue DV.
The pilot flame should be visible through the
door glass in the lower right hand corner
between the front and middle logs. See the
picture below for parts description and view
of normal pilot flame pattern.
ON
OFF
PILOT
HI
LO
PILOT
ADJ
IN
OUT
TO TURN OFF GAS TO BAYVUE DV
1.
When servicing the Bayvue DV, turn off electrical power.
3.
Push in ON/PILOT/OFF control knob and
turn clockwise to “OFF.” Do not force.
turn clockwise to “OFF.” Do not force.
2.
Open the Bayvue DV bottom access panel to see control panel.
4.
Close the Bayvue DV bottom access panel.
FIRST FIRE
Version 1.0h
46
Reduce odor by ventilating the room the first few times the unit is operated. Burn the first two fires no more than 15-
20 minutes. Allow the Bayvue DV to completely cool between burns. Burn the third fire 30-40 minutes and allow
proper cooling time. Operate the appliance according to the instructions contained in this manual.
20 minutes. Allow the Bayvue DV to completely cool between burns. Burn the third fire 30-40 minutes and allow
proper cooling time. Operate the appliance according to the instructions contained in this manual.