Home Automation INC. Omni IIe Manual De Usuario
Program Message Commands
Select the 8 (MESSAGE) key to show, log, clear, say, phone, or send a message. Specify the desired command - See Message.
Select the 8 (MESSAGE) key to show, log, clear, say, phone, or send a message. Specify the desired command - See Message.
MESSAGE
1=SHOW 2=LOG 3=CLEAR
↓
4=SAY 5=PHONE 6=SEND
↑
The 1 (SHOW) key allows you to display the selected text message(s) on the console's top-level display. This can be a helpful
reminder of special events and occasions.
The 2 (LOG) key allows you to store the selected text message(s) in the Event Log. This can be a helpful to keep track of the
times and dates of events and occurrences.
The 3 (CLEAR) key allows you to clear the selected text message, or all text messages from the console's display.
The 4 (SAY) key allows the controller to say the selected voice message over a speaker. This voice message can be an audible
reminder of special events and occasions (i.e. "Front Door Open" when the front door is opened).
The 5 (PHONE) key allows the controller to call the selected phone number and say the selected voice message.
The 4 (SEND) key allows you to send any a text messages through the Pro-Link serial port.
reminder of special events and occasions.
The 2 (LOG) key allows you to store the selected text message(s) in the Event Log. This can be a helpful to keep track of the
times and dates of events and occurrences.
The 3 (CLEAR) key allows you to clear the selected text message, or all text messages from the console's display.
The 4 (SAY) key allows the controller to say the selected voice message over a speaker. This voice message can be an audible
reminder of special events and occasions (i.e. "Front Door Open" when the front door is opened).
The 5 (PHONE) key allows the controller to call the selected phone number and say the selected voice message.
The 4 (SEND) key allows you to send any a text messages through the Pro-Link serial port.
Edit Program Condition
Selecting the 3 (&COND) key, from the Edit Program menu, allows the condition for the program to be specified. The condition
is optional in all program lines. This condition must be true when the program time or event occurs for the program to executed.
Note: Two (2) conditions can be specified in each program line; however, when programming from the console, only 1 condition
can be selected. If 2 conditions must be specified for a single program line, it must be entered using the PC Access Software.
When 2 conditions are part of a single program, the conditions are not displayed on the console. Instead, "&MULTI" is displayed
to let you know that this program line contains 2 conditions. To view or edit the program, you must use the PC Access Software.
The following menu is displayed:
SELECT
is optional in all program lines. This condition must be true when the program time or event occurs for the program to executed.
Note: Two (2) conditions can be specified in each program line; however, when programming from the console, only 1 condition
can be selected. If 2 conditions must be specified for a single program line, it must be entered using the PC Access Software.
When 2 conditions are part of a single program, the conditions are not displayed on the console. Instead, "&MULTI" is displayed
to let you know that this program line contains 2 conditions. To view or edit the program, you must use the PC Access Software.
The following menu is displayed:
SELECT
CONDITION
1=CTRL 2=SEC 3=ZONE
↓
9=TIME #=MISC
↑
After the condition is specified, the display returns to the Edit Program menu.
Program Control Conditions
Press the 1 (CTRL) key to specify that the program should only execute if a specified control unit is either On or Off.
The display prompts for the unit number:
UNIT:
ENTER UNIT
↓
Enter the unit number followed by the ' # ' key, or use the arrow keys to select the unit.
Page 66