Crestron electronic CLS-C6RF Series Prospecto
Note: Additional CNPWS-75 or other Cresnet power supply required beyond 4 devices;
C2N-SDC-DC always requires an additional power supply
C2N-SDC-DC always requires an additional power supply
HOT: (1) Captive screw terminal, line input from 15A or 20A feed
LOAD1 – LOAD6: (6) Captive screw terminals, dimmer channel outputs 1 – 6
NEUTRAL: (1) Captive screw terminal
GROUND: (1) Captive screw terminal
PC (front): (1) 3.5mm TRS mini-phone jack, RS-232 Programming port
LOAD1 – LOAD6: (6) Captive screw terminals, dimmer channel outputs 1 – 6
NEUTRAL: (1) Captive screw terminal
GROUND: (1) Captive screw terminal
PC (front): (1) 3.5mm TRS mini-phone jack, RS-232 Programming port
Controls
Buttons 1 – 6: (6) 3-position rocker pushbuttons; configurable to recall (or toggle
recall/off) individual scenes, control shades, or for master lighting or shade control;
“scene mastering” option enables manual dimming utilizing rocker button action; also
used to adjust lighting levels when in “Lighting” mode and shade positions when in
“Shades” mode; additional functionality configurable via software
recall/off) individual scenes, control shades, or for master lighting or shade control;
“scene mastering” option enables manual dimming utilizing rocker button action; also
used to adjust lighting levels when in “Lighting” mode and shade positions when in
“Shades” mode; additional functionality configurable via software
Up/Down Button: (1) 3-position rocker pushbutton; configurable for master lighting or
shade control, or as a “shift” for Buttons 1-6; other functionality configurable via software
shade control, or as a “shift” for Buttons 1-6; other functionality configurable via software
ON: (1) pushbutton, recalls “On” scene
OFF: (1) pushbutton, turns all lights off
LIGHTS, SHADES: (2) Pushbuttons, select “Lights” or “Shades” modes
SAVE, CANCEL,
OFF: (1) pushbutton, turns all lights off
LIGHTS, SHADES: (2) Pushbuttons, select “Lights” or “Shades” modes
SAVE, CANCEL,
^
,
v
: (4) Pushbuttons, navigate and execute setup functions
Reset: Recessed miniature pushbutton for hardware reset
LED Indicators
Scenes: (6-white) Correspond with each “Scene” Button
High/Low: (2-white) Indicate “Shift” status
ON: (1-white) Indicates “On” Scene is selected
LIGHTS, SHADES: (2-green) Indicates “Lights” or “Shades” mode is active
SAVE, CANCEL: (2-green) Correspond with “Save” and “Cancel” Buttons
MIN, SEC: (2-green) Indicates display of “Minutes” or “Seconds”
1 – 6: (6-green) 7-Segment bargraphs, indicate lighting levels and shade positions
Numeric Display: (2-green) 8-Segment digits, indicates modes and setup values
High/Low: (2-white) Indicate “Shift” status
ON: (1-white) Indicates “On” Scene is selected
LIGHTS, SHADES: (2-green) Indicates “Lights” or “Shades” mode is active
SAVE, CANCEL: (2-green) Correspond with “Save” and “Cancel” Buttons
MIN, SEC: (2-green) Indicates display of “Minutes” or “Seconds”
1 – 6: (6-green) 7-Segment bargraphs, indicate lighting levels and shade positions
Numeric Display: (2-green) 8-Segment digits, indicates modes and setup values
IR Receiver
Reception Frequency: 36 kHz, requires CLS-IRHT8 IR remote (sold separately)
Motion Detector (CLS-C6MRF Only)
Type: Infrared
Range: 20 to 30 feet at 4 foot elevation
Range: 20 to 30 feet at 4 foot elevation
Wireless
RF Transceiver: 2-way RF, 2.4 GHz ISM Channels 11-26 (2400 to 2483.6 MHz), IEEE
802.15.4 compliant
RF Output Power: 10 mW
Range (typical): 150 feet indoor, 250 feet outdoor; subject to site-specific conditions
C2N-MNETGW gateway required
802.15.4 compliant
RF Output Power: 10 mW
Range (typical): 150 feet indoor, 250 feet outdoor; subject to site-specific conditions
C2N-MNETGW gateway required
Environmental
Temperature: 32° to 104°F (0° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Humidity: 10% to 90% RH (non-condensing)
Enclosure
Mounts in a 4-gang electrical box, 3-1/2" deep minimum
Dimensions
Height: 4.48 in (11.38 cm)
Width: 8.89 in (22.58 cm)
Depth: 2.47 in (6.25 cm) for CLS-C6RF, 2.60 in (6.61 cm) for CLS-C6MRF
Width: 8.89 in (22.58 cm)
Depth: 2.47 in (6.25 cm) for CLS-C6RF, 2.60 in (6.61 cm) for CLS-C6MRF
Weight
1.43 lbs (0.65 kg)
* Sold separately
Crestron CLS-C6RF Series ilux
™
Integrated Lighting System w/infiNET
™
Crestron Electronics, Inc. 15 Volvo Drive
l
Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400
l
Fax: 201.767.1903
www.crestron.com
Specifications subject to change without notice. Doc.4826 12/07
All brand names, product names and trademarks are the property of their respective owners.
©2007 Crestron Electronics, Inc.
C2N-DB
Decorator Series Keypad
CNX-B
Designer Series Keypad
C2N-SSC-2
Somfy
®
Shade Controller
C2N-SDC
Shade and Drape Controller (120V AC)
C2N-SDC-DC
Shade and Drape Controller (24V DC)
CLS-IRHT8
IR Handheld Remote
CLS-EXP Series
Lighting Expansion Modules
CLS-C6 or CLS-C6M Series
iLux Integrated Lighting System w/Cresnet
CNPWS-75
Cresnet Power Supply
C2N-MNETGW
infiNET Gateway
C2N-MNETRPT
infiNET Repeater
AVAILABLE ACCESSORIES
Front View
Rear View
8.89 in
(22.58 cm)
4.48 in
(11.38 cm)
IR Receiver
Motion Detector
(CLS-C6MRF only)
(6) configurable
3-position rocker buttons
Setup controls, display, &
PC port behind hinged cover
High/Low LEDs
behind label strip
Label strip
ON LED
ON & OFF
buttons
Up/Down
button
(6) Scene
LEDs
Typical Connections