Shark UV611TR Manual De Usuario
Removal of Battery Pack
1.
Remove the extention handles and dust cup container.
2.
Turn unit over so that the base is facing upwards. Be careful not to turn the unit ON.
3.
With a #1 Phillips screwdiver, remove the screw securing the battery pack
compartment cover to the unit and place aside. (Fig. 5)
compartment cover to the unit and place aside. (Fig. 5)
OPERATING INSTRUCTIONS
Positive Lead
(Red)
Negative Lead
(Black)
Fig. 6
6
Fig. 5
Screw
Battery Pack
Compartment
Cover
Compartment
Cover
Negative
Connector
Positive
Connector
Fig. 7
4.
Carefully lift out battery pack and disconnect the terminals. (Fig. 6)
5.
Connect the terminals to the new battery pack taking care to connect the red lead
(+) to the positive (larger) connector first and the black lead (-) to the negative
(smaller) connector second. (Fig. 7) Place the new battery into the battery
compartment.
(+) to the positive (larger) connector first and the black lead (-) to the negative
(smaller) connector second. (Fig. 7) Place the new battery into the battery
compartment.
6.
Tuck the wiring inside the battery compartment so that the wiring does not interfere
with the battery compartment cover when it is replaced.
with the battery compartment cover when it is replaced.
7. Re-install the battery compartment cover. Please call customer service at
1 (800) 798-7398 if there are any problems removing batteries.
Do NOT attempt to replace the batteries used in this product with any other type of
battery.
battery.
CAUTION:
This appliance contains Ni-Cd batteries. The batteries must be
recycled or disposed of in accordance with local regulations. Please consult your
Yellow Pages or local recycling center for more information.
Yellow Pages or local recycling center for more information.
HOW TO OPERATE YOUR CORDLESS SWEEPER
1.
Before using, please ensure that the cordless sweeper has been initially
charged for 20 hours.
Your cordless sweeper will only operate properly when the batteries are fully
charged. Your sweeper will operate for varying lengths of time on a full charge.
This will depend upon the type of surface being cleaned. (Longer operating time on
bare floors vs. carpets.)
charged for 20 hours.
Your cordless sweeper will only operate properly when the batteries are fully
charged. Your sweeper will operate for varying lengths of time on a full charge.
This will depend upon the type of surface being cleaned. (Longer operating time on
bare floors vs. carpets.)
2.
Push the On/Off switch to operate the unit. To turn off, press switch again. (Fig. 8)
7
OPERATING INSTRUCTIONS
"On/Off“ switch
Fig. 8
Fig. 9
3.
To release the handle to a comfortable position, apply pressure to the top of the
sweeper head with your foot while pulling back on the handle. (Fig. 9)
sweeper head with your foot while pulling back on the handle. (Fig. 9)
4.
To change the speed of the brush roll, press the speed control button once. One
light “On” indicates the unit is on the optimal speed for cleaning hard floors. Two
lights “On” indicate the unit is on the optimal speed for cleaning carpets.
light “On” indicates the unit is on the optimal speed for cleaning hard floors. Two
lights “On” indicate the unit is on the optimal speed for cleaning carpets.
ANTI-JAM BRUSH ROLL FEATURE
This feature protects your unit’s motor from damage due to overheating, that may be
caused by the rotating brush gets jammed or tangled in something. If the rotating brush
becomes overloaded it will stop turning and both speed indicator lights will remain lit at
the same time. To reset the unit:
1.
caused by the rotating brush gets jammed or tangled in something. If the rotating brush
becomes overloaded it will stop turning and both speed indicator lights will remain lit at
the same time. To reset the unit:
1.
Press On/Off switch.
2.
Remove the transparent brush cover from the sweeper power head to remove any
build up of lint, hair or fiber on the rotating brushes.
build up of lint, hair or fiber on the rotating brushes.
3.
Wait for 10 seconds to allow the unit to cool down.
4.
Press “On/Off switch again, the unit should restart.