Aiwa XH-A1000 Guía De Operación
30
ENGLISH
SETTING THE TIMER
The unit can be turned on at a specified time every day with the
built-in timer.
built-in timer.
Preparation
Make sure the clock is set correctly.
Make sure the clock is set correctly.
1 Press one of the function buttons to select a
source.
2 Press TIMER once so that
appears on the
display.
Time and audio source name flash alternately.
3 Within 6 seconds, turn MULTI JOG to designate
the timer-on time, then press ENTER or
a
.
Turning MULTI JOG changes both the hour and the minute.
f
or
g
is also available instead of MULTI JOG. Holding
these buttons down will vary the time rapidly.
4 Within 4 seconds, turn MULTI JOG to select the
duration for the timer-activated period.
The duration can be set between 5 and 240 minutes in 5-
minute steps.
minute steps.
f
or
g
is also available instead of MULTI JOG.
The duration will be automatically set after 4 seconds. It will
also be set if ENTER or
also be set if ENTER or
a
is pressed within 4 seconds after
step 4.
5 Adjust the volume.
The source sound will play at the volume level set in this step
when the power is turned on by the timer.
If the volume level is set to 21 or higher, however, it will
automatically be set to 20 when the power is turned on.
when the power is turned on by the timer.
If the volume level is set to 21 or higher, however, it will
automatically be set to 20 when the power is turned on.
6 Prepare the source.
To listen to a CD, load the disc to be played first on tray 1.
To listen to a tape, insert the tape into the cassette tray.
To listen to the radio, select the band and tune in to a station.
To listen to a tape, insert the tape into the cassette tray.
To listen to the radio, select the band and tune in to a station.
7 Press POWER to turn off the power.
remains on the display after the power is turned off (timer
standby mode) if the power-economizing mode is OFF.
When the timer-on time is reached, the unit turns on and
begins play with the selected source.
begins play with the selected source.
To check the timer setting
Press TIMER.
The selected source, the timer-on time, and the duration for the
timer-activated period will be displayed for 6 seconds.
Press TIMER.
The selected source, the timer-on time, and the duration for the
timer-activated period will be displayed for 6 seconds.
To change any of the previous setting
Carry out from step 1.
However, if you do not change the timer-on time, in step 3 just
press ENTER twice and continue from step 4.
Carry out from step 1.
However, if you do not change the timer-on time, in step 3 just
press ENTER twice and continue from step 4.
To cancel the timer standby mode temporarily
Press TIMER repeatedly until
disappears and “ OFF” is
displayed.
To restore the timer standby mode, press TIMER once or twice
To restore the timer standby mode, press TIMER once or twice
to display
or
REC.
Using the unit while the timer is set
You can use the unit normally after setting the timer.
Before turning off the power, carry out step 5 and 6.
You can use the unit normally after setting the timer.
Before turning off the power, carry out step 5 and 6.
NOTE
• You can change the source that was selected in step 1 by
pressing one of the function buttons before pressing ENTER
or
or
a
in step 3.
• If the power-economizing mode is ON,
is not displayed in
the timer standby mode.
• Timer playback and timer recording will not begin unless the
power is turned off.
• Connected equipment cannot be turned on and off by the built-
in timer of this unit. Use an external timer.
MULTI
JOG
JOG
TIMER
ENTER
Function
buttons
buttons
VOLUME
POWER
a
TIMER
Function
buttons
buttons
a
f
,
g
f
,
g
VOL /