Creek Audio Destiny Manual De Usuario
SAFETY INSTRUCTIONS CONT’D
DESTINY RDS FM/AM TUNER OPERATING INSTRUCTIONS
Page Two
DAMAGE REQUIRING SERVICE
Stop using the unit immediately and have it inspected by an authorised service centre whenever:
1.
The power supply cord or plug has been damaged.
2.
Liquid has been spilled into the unit.
3.
The unit has been exposed to rain.
4.
The unit does not operate properly.
5.
The unit has been dropped or damaged.
6.
Smoke or any unusual smell is detected from the unit.
CAUTION: To reduce the risk of electric shock, do not remove cover. No serviceable parts inside.
FRONT PANEL
FRONT PANEL CONTROLS & OPERATION
TUNING
Turn the knob left or right to manually fine tune stations after switching Mode to tuning. When tuned to the maximum
frequency, it is possible to go to the minimum frequency quickly by continuing to turn the knob clockwise. The
frequency will flip to the bottom 87.5Mhz on FM.
Turn the knob left or right to manually fine tune stations after switching Mode to tuning. When tuned to the maximum
frequency, it is possible to go to the minimum frequency quickly by continuing to turn the knob clockwise. The
frequency will flip to the bottom 87.5Mhz on FM.
PRE-SET
Steps up or down through pre-set stations by turning the knob on the right after switching Mode to Pre-set. When
using Pre-set mode, after reaching the last stored station in FM, the tuner will flip to any stored stations in AM, then
back to FM if the knob is turned back or forward through all of the stored AM stations.
Steps up or down through pre-set stations by turning the knob on the right after switching Mode to Pre-set. When
using Pre-set mode, after reaching the last stored station in FM, the tuner will flip to any stored stations in AM, then
back to FM if the knob is turned back or forward through all of the stored AM stations.
MODE
Press this button to select manual tuning or pre-set mode, when using the knob on the right of the panel. The
button toggles between the 2 functions and the display will either show the pre-set station number, say 12F, for the
station pre-set 12, or it will show 00F at the beginning to indicate free tuning and not pre-set.
Press this button to select manual tuning or pre-set mode, when using the knob on the right of the panel. The
button toggles between the 2 functions and the display will either show the pre-set station number, say 12F, for the
station pre-set 12, or it will show 00F at the beginning to indicate free tuning and not pre-set.
SCAN
Pressing the Scan button will automatically search for the next tuned (strong) station. If you want to keep it, follow the
"Store" procedure described below.
Pressing the Scan button will automatically search for the next tuned (strong) station. If you want to keep it, follow the
"Store" procedure described below.
STORE
Use to set a station pre-set. Tune to the station you wish to save as a pre-set. Press the STORE button then press the
MODE button (to select the PRE-SET mode). The band (FM or AM) and a pre-set number will be displayed and begin to
flash. Turn the tuning/preset knob on the front panel until the desired number is displayed then press the STORE
button. Any number from 1- 80 can be used for AM or FM pre-sets. Pre-sets can be set faster by using the remote
control.
Use to set a station pre-set. Tune to the station you wish to save as a pre-set. Press the STORE button then press the
MODE button (to select the PRE-SET mode). The band (FM or AM) and a pre-set number will be displayed and begin to
flash. Turn the tuning/preset knob on the front panel until the desired number is displayed then press the STORE
button. Any number from 1- 80 can be used for AM or FM pre-sets. Pre-sets can be set faster by using the remote
control.
STANDBY
Press this button to turn the tuner on and off. In standby, this product draws less than 1 Watt of power. However,
if you are leaving the unit switched off for a long period, it is advisable to switch it off permanently by using the
POWER SWITCH on the rear panel.
Press this button to turn the tuner on and off. In standby, this product draws less than 1 Watt of power. However,
if you are leaving the unit switched off for a long period, it is advisable to switch it off permanently by using the
POWER SWITCH on the rear panel.