Everpure EV3112 Manual De Usuario
cArtriDge cHAnge proceDure
e-Series prefilter cartridge change
1. Shut off power to equipment. Shut
off inlet water ahead of system.
2. Push red relief valve. Unscrew
bowl. Remove prefilter cartridge.
3. Clean bowl with filtered water only;
NO SPECIAL CLEANERS.
4. Feel head o-ring. If dry, lubricate
with high quality silicone lubricant.
5. Install new prefilter cartridge in
bowl. Hand tighten bowl onto head.
6. Turn on water. Turn on power to
equipment.
everpure carbon filter cartridge
change
change
1. Shut off power to equipment. Shut
off inlet water ahead of system.
2. Open flushing valve to relieve
pressure.
3. Hold head firmly and push upward.
Turn cartridge to left until it stops.
4. Pull cartridge downward and out of
head.
5. Hold head firmly. Align cartridge
lug with label. Insert new cartridge
firmly into head.
firmly into head.
6. Turn cartridge right 90˚ until
rotation stops.
7. Repeat steps 3-6 for remaining
cartridges.
flushing
8. With flushing valve fully open, open
inlet water at full force for five
minutes. Close flushing valve.
minutes. Close flushing valve.
9. Turn on power to equipment
preSSure gAugeS
Low Inlet
Pressure
Adequate Inlet
Pressure
Low Outlet
Pressure
Adequate Outlet
Pressure
Sr-X feeder cartridge change
1. Shut off power to equipment. Shut
off inlet water ahead of system.
2. Press red pressure relief button on
head.
3. Unscrew bowl.
4. Remove old cartridge.
5. Feel bowl o-ring; if dry, lubricate
with silicone lubricant.
6. Install new SS-10 cartridge into
head.
7. Hand tighten bowl into head.
8. Turn on water.
9. Press red pressure relief button
until water comes out of valve port.
10. Turn on power to equipment.
for installations in Massachusetts, the commonwealth of Massachusetts plumbing code 248 cMr shall be adhered to. consult your licensed
plumber for installation of the system. this system and its installation must comply with state and local regulations.
plumber for installation of the system. this system and its installation must comply with state and local regulations.
cArtriDge cHAnge DeterMinAtion
Replace the prefilter cartridge whenever it becomes excessively dirty (observed visually or by flow restriction). Follow the change instructions provided with
the cartridge. Replace carbon filter cartridges when capacity is reached or when flow becomes inadequate, but at least annually. All carbon filter cartridges
on multiple cartridge systems should be changed at the same time. Change the SS-10 cartridge when product level in the cartridge drops below 1/2" from
the bottom of the bowl.
The system pressure gauge or optional Everguard
the cartridge. Replace carbon filter cartridges when capacity is reached or when flow becomes inadequate, but at least annually. All carbon filter cartridges
on multiple cartridge systems should be changed at the same time. Change the SS-10 cartridge when product level in the cartridge drops below 1/2" from
the bottom of the bowl.
The system pressure gauge or optional Everguard
™
Low Pressure Alarm (LPA) provides a quick, simple means of determining when the filter cartridge(s)
should be checked. Installed on the system outlet manifold, the gauge or LPA can be used to monitor both dynamic (flowing) and static (line) pressure. The
cartridge(s) should be changed when the pressure gauge is in the red area while equipment is in operation, and yet the needle shows adequate line pressure
between cycles. Observe the needle during the next equipment on cycle. If the needle registers adequate pressure, it can be assumed that the temporary
low-pressure condition was caused by a brief power failure or other incoming pressure disruption. If the low pressure condition is not due to an external
condition, check/change the prefilter first. If the low pressure condition is still not corrected, change the carbon filter cartridges.
cartridge(s) should be changed when the pressure gauge is in the red area while equipment is in operation, and yet the needle shows adequate line pressure
between cycles. Observe the needle during the next equipment on cycle. If the needle registers adequate pressure, it can be assumed that the temporary
low-pressure condition was caused by a brief power failure or other incoming pressure disruption. If the low pressure condition is not due to an external
condition, check/change the prefilter first. If the low pressure condition is still not corrected, change the carbon filter cartridges.