Yamaha RX-V461 Manual De Usuario
43
En
XM Satellite Radio tuning
English
BA
S
IC
OPERA
T
ION
y
Before performing operations, set the operation mode selector
(
(
K) to SOURCE and then press AXM to select “XM” as the
input source.
■ All Channel Search mode
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “ALL CH
SEARCH”.
SEARCH”.
2
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to search
for a channel within all channels.
y
• You can search for a channel quickly by pressing and holding
5PRESET/TUNING/CH l / h (or DPRESET/CH k / n).
• To display the XM Radio ID number displayed in the front
panel display, select channel “0”.
■ Category Search mode
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “CAT SEARCH”.
2
Press 4
CATEGORY (or DA-E/CAT. l / h)
repeatedly to change the channel category.
3
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to search
for a channel within the selected channel
category.
category.
y
You can search for a channel quickly by pressing and holding
5PRESET/TUNING/CH l / h (or DPRESET/CH k / n).
5PRESET/TUNING/CH l / h (or DPRESET/CH k / n).
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting XM Satellite Radio preset channels”
on page 44.
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting XM Satellite Radio preset channels”
on page 44.
y
All preset channels (A1 to E8) recalls “001 Preview” by the initial
factory setting.
factory setting.
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “PRESET
SEARCH”.
SEARCH”.
2
Press 4
CATEGORY (or DA-E/CAT. l / h)
repeatedly to change the preset channel
group (A to E).
group (A to E).
3
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to change
the preset channel number (1 to 8).
y
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) on the remote control.
pressing the numeric buttons (1 to 8) on the remote control.
■ Direct Number Access mode
1
Press N
SRCH MODE repeatedly to select
“ALL CH SEARCH” or “CAT SEARCH”.
2
Press the numeric buttons (
B) to enter the
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons as shown below.
For example, to enter the number 123, press the
numeric buttons as shown below.
The display changes as follows.
y
• To enter a one-digit or two-digit channel number, press the
numeric buttons (
B) and then press MENT to confirm the
input number. Instead of pressing MENT to tune into the
channel immediately, you can wait a few seconds until this
unit confirms the entered channel number.
channel immediately, you can wait a few seconds until this
unit confirms the entered channel number.
• If no button is pressed within a few seconds after you enter
a one-digit or two-digit number, this unit automatically
confirms the entered channel number.
confirms the entered channel number.
• Pressing a button other than the numeric buttons (
B) or
MENT cancels the Direct Number Access mode
procedure.
procedure.
1
CLASSICAL
2
LIVE/CLUB
3
ENTERTAIN
<XM> --1
<XM> -12
<XM>123