Yamaha RX-V3300 Manual De Usuario
14
SPEAKER SETUP
AC OUTLETS
AC IN
MAIN
(SURROUND)
CENTER
FRONT
REAR
EFFECT
IMPEDANCE SELECTOR
SELECTEUR D'INPEDANCE
SET BEFORE POWER ON
L
L
L
L
L
+
+
+
+
+
+
ZONE 2 OUT
MAIN A OR B
CENTER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
FRONT
REAR
REAR
REAR CENTER
:
:
:
:
:
:
:
ZONE 2 OUT
MAIN A OR B
CENTER
6
ΩMIN./SPEAKER
6
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
FRONT
REAR
REAR
REAR CENTER
:
:
:
:
:
:
:
A + B
8
ΩMIN./SPEAKER
:
A
B
IMPEDANCE SELECTOR
SELECTEUR D'INPEDANCE
SET BEFORE POWER ON
ZONE 2 OUT
MAIN A OR B
CENTER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
8
ΩMIN./SPEAKER
FRONT
REAR
REAR
REAR CENTER
:
:
:
:
:
:
:
ZONE 2 OUT
MAIN A OR B
CENTER
6
ΩMIN./SPEAKER
6
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
4
ΩMIN./SPEAKER
FRONT
REAR
REAR
REAR CENTER
:
:
:
:
:
:
:
A + B
8
ΩMIN./SPEAKER
:
Switch
position
Upper
Lower
Speaker
Zone 2
Front
Effect
Rear
Center
Rear
Center
Main
Zone 2
Front
Effect
Rear
Center
Rear
Center
Main
Impedance level
The impedance of each speaker must be 6
Ω or higher.
The impedance of each speaker must be 6
Ω or higher.
The impedance of each speaker must be 4
Ω or higher.
[Australia model]
The impedance of each speaker must be 6
The impedance of each speaker must be 6
Ω or higher.
The impedance must be 4
Ω or higher.
The impedance must be 4
Ω or higher.
[Australia model]
The impedance must be 6
The impedance must be 6
Ω or higher.
If you use one set of main speakers, the impedance of
each speaker must be 4
each speaker must be 4
Ω or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 8
each speaker must be 8
Ω or higher.
The impedance of each speaker must be 8
Ω or higher.
The impedance of each speaker must be 8
Ω or higher.
The impedance of each speaker must be 8
Ω or higher.
The impedance must be 8
Ω or higher.
The impedance must be 8
Ω or higher.
If you use one set of main speakers, the impedance of
each speaker must be 8
each speaker must be 8
Ω or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16
each speaker must be 16
Ω or higher.
[U.S.A. model]
The impedance of each speaker must be 8
The impedance of each speaker must be 8
Ω or higher.
IMPEDANCE SELECTOR switch
■ IMPEDANCE SELECTOR switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the
standby mode.
Select the upper or lower position according to the impedance of the speakers in your system. Be sure to move this
switch only when this unit is in the standby mode.
switch only when this unit is in the standby mode.
(U.S.A. model)
0103V3300_10-23_EN(UA)
02.8.21, 6:59 PM
14