Telex PAM-32 Manual De Usuario
21
Service Menu
1.
Select Min Volume from the Service menu, then tap PGM.
♦Speaker displays.
♦Speaker displays.
2.
Press
⎠⎠ to select either Speaker or Headset.
3.
Tap PGM.
4.
Press
⎠⎠ or −− to increase or decrease the minimum volume level. The range is -24dB to -60dB or full Mute.
5.
Tap PGM.
6.
Tap CLR to exit.
7.
Run Service Menu, Save Cfg to store Min Volume settings.
Service Menu, Mod Assign
NOTE: Normally, this is a service adjustment that is required only when replacing a key an display module. It may also be
required if for some reason, the key assignments, as displayed in AZedit, appear to be in the wrong positions on the keypanel
or expansion panel.
required if for some reason, the key assignments, as displayed in AZedit, appear to be in the wrong positions on the keypanel
or expansion panel.
The PAM-32 and the EKP-32 use module ID numbers (Mod ID numbers) to define the address of each key and display
module. By default, Mod 1 is always assigned to the right half of the PAM-32 and this never changes, since this module has the
keypad and is unique. However, the rest of the modules are identical. When replacing any of these modules, you may have to
reset the Mod ID number as follows:
module. By default, Mod 1 is always assigned to the right half of the PAM-32 and this never changes, since this module has the
keypad and is unique. However, the rest of the modules are identical. When replacing any of these modules, you may have to
reset the Mod ID number as follows:
1.
Select Mod Assign from the Service menu, then tap PGM.
Cancel? displays.
Cancel? displays.
To exit the procedure without making changes, tap PGM.
All the alphanumeric displays, except Mod 1, will appear as shown below.
All the alphanumeric displays, except Mod 1, will appear as shown below.
2.
Assign the Mod IDs as shown. Repeat the procedure for each module.
NOTE: You do not need to run Save Cfg after changing Mod assignments.
Service Menu, Ref Level
Allows the adjustment of the nominal audio output level to the matrix from 0dB to +8dB.
1.
Select Outp Level, then tap PGM.
+8dB displays
¯ ¯ decreases the level
-- increases the level
+8dB displays
¯ ¯ decreases the level
-- increases the level
2.
Tap PGM.
Call waiting
1F01 DAN KP96 KP96 SL03 KP12 M009
---- ---- ---- ---- WKP4 ---- WKP4
KP12 OKP4 ANDY KP32 DAN KP96 TIF1 KP12
---- ---- ---- ---- ---- ---- ---- ----
Listen
Talk
Listen
Talk
™
EKP-32
Call waiting
Headset
Vol.
MENU
FWD
BACK
MUTE
CLR
PGM
NUM
SLIST
1
PL
IFB
2
AUTO
ISO
3
PHONE
RELAY
4
PREFIX
TYPE
5
6
COPY CW
EX COPY
7
E-PNL
DISPLAY
8
9
MULT
FUNC
0
1F01 DAN KP96 KP96 SL03 KP12 M009
---- ---- ---- ---- WKP4 ---- WKP4
KP12 OKP4 ANDY KP32 DAN KP96 TIF1 KP12
---- ---- ---- ---- ---- ---- ---- ----
Listen
Listen
Headset
Vol. Sel.
™
PAM-32
PAM-32
EKP-32
↓ ↓ Increase
Select Module ID 0
↓ ↓ Decrease
Select
↓ ↓
1. Module ID number
is displayed here
2.Select the correct module ID
number with these keys
(see below)
3. Tap here to assign.
Asterisks will briefly display
while the module updates.
ID 0
I D 1
( C a n n o t c h a n g e )
I D
2
I D 3