Knoll 6K Manual De Usuario
10. Connect the AC power into an outlet that supplies at least
six amps (750 watts) dedicated to each 6k (four amps to 4K).
six amps (750 watts) dedicated to each 6k (four amps to 4K).
Caution: Never listen to sound that is distorted. If distorted
sound is heard, turn the volume down immediately or speaker
and/or amplifier damage could occur that is not covered by the
and/or amplifier damage could occur that is not covered by the
warranty. If this problem persists, contact your dealer.
User adjustments and service: Other than a gain or volume
adjustment, there are no user adjustments on the 4K or 6K.
Your installer may make certain gain level adjustments on the
adjustment, there are no user adjustments on the 4K or 6K.
Your installer may make certain gain level adjustments on the
rear panel.
Caution: The 4K or 6K contain no user serviceable parts, so do
not attempt to open or repair the 4K or 6K. Refer servicing to a
not attempt to open or repair the 4K or 6K. Refer servicing to a
qualified technician only or contact the factory for information.
Caution: NEVER connect the 4K or
6K to impedances less than 4
ohms or amplifier damage not
covered by the warranty may
occur.
The trigger is 12 VDC (35mA per 4K or 6K) via 3.5mm
mono jack. 5 VDC trigger outputs will not work. To
connect the trigger to a receiver use a 12 VDC power
supply (we suggest Knoll PS1202 power supply with an
mono jack. 5 VDC trigger outputs will not work. To
connect the trigger to a receiver use a 12 VDC power
supply (we suggest Knoll PS1202 power supply with an
adaptor). Plug the power supply into the switched outlet
on the rear of the receiver. Connect the 12 volt wire to a
3.5mm mono jack. Plug the jack into the rear of the 4K or
6K. 12 VDC polarity is not important. Make sure the
amplifier power switch is off (out). When the receiver is
switched on, the 4K or 6K amplifier is switched on.
on the rear of the receiver. Connect the 12 volt wire to a
3.5mm mono jack. Plug the jack into the rear of the 4K or
6K. 12 VDC polarity is not important. Make sure the
amplifier power switch is off (out). When the receiver is
switched on, the 4K or 6K amplifier is switched on.
-
The Link button is normally set to the in
position to give all six stereo inputs individual
sources. When the Link button is set to the
out position, that input Left/Right is linked or
cascaded to input #1 (without the use of Y cords). Any or
position to give all six stereo inputs individual
sources. When the Link button is set to the
out position, that input Left/Right is linked or
cascaded to input #1 (without the use of Y cords). Any or
all combination of linked inputs 2 to inputs 6 are possible.
When all inputs are linked to input 1 the input impedance
is about 4000 ohms.
When all inputs are linked to input 1 the input impedance
is about 4000 ohms.
12 VDC
Trigger
120 VAC
8 Amps
6K Amplifier
Ga
1L 1R
Input
1
L
2
R
Output
L+
L-
L-
R+
R-
R-
R+
Gain
3L 3R
ut
4L 4R
3
L
4
R
Output
L+
L-
L-
L+
R+
R-
R
R+
Gain
5L 5R
Input
6L 6R
5
L
6
R
Output
L+
L-
L-
L+
R+
R-
R-
R+
1
2
3
4
5
6
L+
Inp
in
2L 2R