Crate Amplifiers GX-140CH Manual De Usuario
1
2
3
4
6
7
8
10
11
12
13
14
15
19
20
21
16
5
9
17 18
FRONT PANEL:
1: INPUT: Connect your guitar here using a shielded
instrument cable.
instrument cable.
OVERDRIVE CHANNEL: A high gain channel giving you
sounds from a slight edge to serious overdrive.
sounds from a slight edge to serious overdrive.
2: GAIN 1: When active, sets the amount of compression
and distortion from the amplifier. At far left, the sound will
have a thick compressed quality. As you turn the control to
the right the amount of distortion increases. Gain 1 pro-
duces less intense distortion than Gain 2 and is active only
when the Gain Select switch (#5) is out.
and distortion from the amplifier. At far left, the sound will
have a thick compressed quality. As you turn the control to
the right the amount of distortion increases. Gain 1 pro-
duces less intense distortion than Gain 2 and is active only
when the Gain Select switch (#5) is out.
3: GAIN 2: When active, sets the amount of compression
and distortion from the amplifier. At far left, the sound will
have a thick compressed quality. As you turn the control to
the right the amount of distortion increases. Gain 2 is pro-
duces more intense distortion than Gain 1 and is active
only when the Gain Select switch (#5) is in.
and distortion from the amplifier. At far left, the sound will
have a thick compressed quality. As you turn the control to
the right the amount of distortion increases. Gain 2 is pro-
duces more intense distortion than Gain 1 and is active
only when the Gain Select switch (#5) is in.
4: SHAPE: Working in conjunction with the Gain 2 control,
rotate the Shape control until you find the sound you’re
looking for. Turning the control towards the left enhances
the mid frequencies; turning it to the right enhances the low
and high frequencies. (Only affects Gain 2 when active.)
rotate the Shape control until you find the sound you’re
looking for. Turning the control towards the left enhances
the mid frequencies; turning it to the right enhances the low
and high frequencies. (Only affects Gain 2 when active.)
5: GAIN SELECT: Switches between Gain 1 (out) and
Gain 2 (in). A footswitch (see #28, rear panel) overrides
this switch.
Gain 2 (in). A footswitch (see #28, rear panel) overrides
this switch.
6: LOW: Adjusts the low frequency output level: to the left
reduces the low frequency output; to the right increases it.
This control allows a range of 10dB at 80Hz.
reduces the low frequency output; to the right increases it.
This control allows a range of 10dB at 80Hz.
7: HIGH: Adjusts the high frequency output level: to the left
reduces the high frequency output, to the right increases it.
This control allows a range of 10dB at 7kHz.
reduces the high frequency output, to the right increases it.
This control allows a range of 10dB at 7kHz.
8: LEVEL: Sets the output volume level from Channel A: in
the far-left position there is no output; turning the control to
the right increases the output. Use this control along with
the Gain and Shape controls (#2, 3 & 4) to create a wide
variety of sounds.
the far-left position there is no output; turning the control to
the right increases the output. Use this control along with
the Gain and Shape controls (#2, 3 & 4) to create a wide
variety of sounds.
9: CHANNEL SELECT: When this switch is pressed in the
Overdrive Channel is engaged. The Clean Channel is
selected when this switch is out. A footswitch (see #28, rear
panel) overrides this switch. The adjacent LEDs indicate
which channel is selected.
Overdrive Channel is engaged. The Clean Channel is
selected when this switch is out. A footswitch (see #28, rear
panel) overrides this switch. The adjacent LEDs indicate
which channel is selected.
CLEAN CHANNEL: A normal gain channel designed to
give you crystal clear sounds.
give you crystal clear sounds.
10: LEVEL: Sets the output volume level from the Clean
Channel: in the far-left position there is no output; turning
the control to the right increases the output level.
Channel: in the far-left position there is no output; turning
the control to the right increases the output level.
11: LOW: Adjusts the low frequency output level: to the left
reduces the low frequency output; to the right increases it.
This control allows a range of 20dB at 100Hz.
reduces the low frequency output; to the right increases it.
This control allows a range of 20dB at 100Hz.
12: MID: Adjusts the mid frequency output level: to the left
reduces the midrange output; turning it to the right increas-
es it. This control allows a range of 14dB at 700Hz.
reduces the midrange output; turning it to the right increas-
es it. This control allows a range of 14dB at 700Hz.
13: HIGH: Adjusts the high frequency output level: to the
left reduces the high frequency output; to the right increas-
es it. This control allows a range of 27dB at 10kHz.
left reduces the high frequency output; to the right increas-
es it. This control allows a range of 27dB at 10kHz.
14: REVERB, OVERDRIVE: Adjust the amount of reverb
for the Overdrive Channel with this control: in the full-left
position the output signal is “dry” (no reverb); rotating the
control to the right increases the amount of effect.
for the Overdrive Channel with this control: in the full-left
position the output signal is “dry” (no reverb); rotating the
control to the right increases the amount of effect.
15: REVERB, CLEAN: Adjust the amount of reverb for the
Clean Channel with this control: in the full-left position the
output signal is “dry” (no reverb); rotating the control to the
right increases the amount of effect.
Clean Channel with this control: in the full-left position the
output signal is “dry” (no reverb); rotating the control to the
right increases the amount of effect.
16: INSERT LOOP: Connect an external effects device via
this jack. Use a stereo 1/4” male Y-cord: ring = send, tip =
return, sleeve = ground. See the illustration on the panel to
the right for more information. This is a mono pre-chorus
effects loop.
this jack. Use a stereo 1/4” male Y-cord: ring = send, tip =
return, sleeve = ground. See the illustration on the panel to
the right for more information. This is a mono pre-chorus
effects loop.
17: CHORUS ON/OFF: Turn the Chorus/Expander on and
off with this switch. When the switch is pressed in, the
Chorus/Expander is active. A footswitch (see #29, rear
panel) overrides this switch.
off with this switch. When the switch is pressed in, the
Chorus/Expander is active. A footswitch (see #29, rear
panel) overrides this switch.
18: CHORUS/EXPANDER: Select between the built-in
stereo chorus or the “expander” circuit with this switch.
When the switch is pressed in, the chorus section is select-
ed. When the switch is out, the amplifier’s expander circuit
is activated, giving the sound a wide-open, “spatial” effect.
In order for either effect to be active, the Chorus On/Off
switch (#17) must be pressed in.
stereo chorus or the “expander” circuit with this switch.
When the switch is pressed in, the chorus section is select-
ed. When the switch is out, the amplifier’s expander circuit
is activated, giving the sound a wide-open, “spatial” effect.
In order for either effect to be active, the Chorus On/Off
switch (#17) must be pressed in.
19: DEPTH: Set the intensity of the chorus effect with this
control: in the far left position there will be almost no cho-
rus; as you rotate the control to the right the amount of
effect increases.
control: in the far left position there will be almost no cho-
rus; as you rotate the control to the right the amount of
effect increases.
20: RATE: Set the speed of the chorus effect with this con-
trol: to the left for slow, smooth “phasing” sounds, to the
right for faster “vibrato” sounds.
trol: to the left for slow, smooth “phasing” sounds, to the
right for faster “vibrato” sounds.
21: POWER SWITCH: Turns the amplifier ON in the up
position, off in the down position. The Channel LED for the
selected channel will light when the amp is switched on.
position, off in the down position. The Channel LED for the
selected channel will light when the amp is switched on.
GX-140C/CH Amplifier