MK Sound MX-125 MK II Manual De Usuario
page 5
powered subwoofers
STANDARD AMPLIFIER/SPEAKER WIRE CONNECTIONS
Many M&K subwoofer owners hook up their Subwoofer by connecting it to their receiver or
amplifier using speaker wires. To do so, you make the same kind of connections that you would use
for your Satellite (or main) speakers, except that both the left and right channels go to the Subwoofer.
(If you are using two Subwoofers, connect one channel only to each Subwoofer).
for your Satellite (or main) speakers, except that both the left and right channels go to the Subwoofer.
(If you are using two Subwoofers, connect one channel only to each Subwoofer).
NOTE: You cannot connect the MX-125 Mk II using speaker wires. If you have to connect an
MX-125 Mk II to an amplifier or receiver does not have RCA outputs, please contact your dealer or the
M&K factory. We offer an optional RM-2 High Level to Low Level convertor with Remote Volume
Control, which will allow you to drive the MX-125 Mk II with speaker-level amplifier outputs.
M&K factory. We offer an optional RM-2 High Level to Low Level convertor with Remote Volume
Control, which will allow you to drive the MX-125 Mk II with speaker-level amplifier outputs.
1.
Run speaker wire between the Amplifier's Left channel output terminals and the
Subwoofer's Left channel "FROM AMPLIFIER" terminals.
Subwoofer's Left channel "FROM AMPLIFIER" terminals.
a.
Connect the Amplifier's Left channel Positive (+) terminal and the Subwoofer's
Left RED (+) "FROM AMPLIFIER" terminal.
Left RED (+) "FROM AMPLIFIER" terminal.
b.
Connect the Amplifier's Left channel Negative ( — ) terminal and the Subwoofer's
Left BLACK ( — ) "FROM AMPLIFIER" terminal.
Left BLACK ( — ) "FROM AMPLIFIER" terminal.
2.
Make matching connections for the Right channel. See Figure 1.
FIGURE 1 - TO AN AMPLIFIER USING SPEAKER WIRES
IMPORTANT NOTE FOR DOLBY SURROUND SOUND SYSTEMS:
When the Subwoofer is connected to the Left and Right amplifier outputs, and the controller is in
Pro-Logic mode, the Center channel WIDE/NORMAL switch MUST be set to the NORMAL mode. If
the switch is set to the WIDE mode, the bass content of the Center channel will not be fed to the
Subwoofer, and a significant amount of bass in the program material will not be reproduced.
the switch is set to the WIDE mode, the bass content of the Center channel will not be fed to the
Subwoofer, and a significant amount of bass in the program material will not be reproduced.
100
PHASE
10391 Jefferson Blvd, Culver City, CA 90232 310/204-2854
MILLER & KREISEL SOUND CORPORATION
RIGHT
RIGHT
FROM PREAMP
BASS LEVEL
LOW PASS FILTER
(Hz)
FROM AMPLI
FIER
MAX
50
75
60
125
Made in U.S.A.
T
4 AMP
120 VAC 50/60 Hz
TO SPEAKERS
LEFT
RIGHT
LE
FT
MIN
LEFT/MONO
SLOW-BLOW
ATTENTION:
DEBRANCHER AVANT DE
REMPLACER LE FUSIBLE.
UTILIZER UN FUSIBLE
DE RECHANGE DE MEME TYPE.
CAUTION:
DISCONNECT SUPPLY CORD
BEFORE CHANGING FUSE.
REPLACE FUSE ONLY
WITH SAME TYPE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS:
RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
+
AMPLIFIER OR RECEIVER
L
R
This option is not available
with the MX-125 Mk II
with the MX-125 Mk II