Manualsbrain.com
  1. Manuales
  2. Marcas
  3. Yamaha
  4. aw1600
  5. Manual De Usuario

Yamaha aw1600 Manual De Usuario

Descargar
Página de 232
AW1600  Owner’s Manual
Connecting a digital recorder such as MD or DAT
15
178
Using the A
W1600 with e
xter
nal de
vices
To play back your digital recorder and listen to the 
recorded result, connect the DIGITAL STEREO OUT 
jack of your digital recorder to the AW1600’s DIGI-
TAL STEREO IN jack, and perform the following 
steps.
7
If you want to hear the result that was 
recorded on the digital recorder, lower the 
[STEREO] fader to the –
 
∞
 position, and 
use the [UTILITY] key to access the D.IN - 
HDD page of the UTILITY screen.
8
Move the cursor to the DIGITAL REC ON/
OFF button, and press the [ENTER] key.
A message will ask you to confirm your observance of 
copyright laws. If you accept the conditions described 
in “Copyright Notice” (
→ p. 6), move the cursor to the 
OK button and press the [ENTER] key. The DIGITAL 
REC ON/OFF button will be switched ON, and digital 
audio data input will be enabled.
9
Move the cursor to the DIGITAL PATCH IN 
field, and turn the [DATA/JOG] dial to select 
“STEREO BUS” as the destination for the 
input signal from the DIGITAL STEREO IN 
jack.
With this setting, the input signal from the DIGITAL 
STEREO IN jack will be connected directly to the ste-
reo bus.
10
Raise the [STEREO] fader to the 0 dB posi-
tion, and play back your digital recorder.
Here’s how the signal from a digital recorder connected to 
the DIGITAL STEREO IN jack can be recorded on an 
AW1600 track while still in the digital domain.
1
Lower the [STEREO] fader to the –
 
∞
 posi-
tion.
2
As shown in the diagram below, connect 
your digital recorder to the AW1600.
3
Use the [UTILITY] key to access the D.IN • 
HDD page of the UTILITY screen.
4
Move the cursor to the DIGITAL REC ON/
OFF button, and press the [ENTER] key.
A message will ask you to confirm your observance of 
copyright laws. If you accept the conditions described 
in “Copyright Notice” (
→ p. 6), move the cursor to the 
OK button and press the [ENTER] key. The DIGITAL 
REC ON/OFF button will be switched ON, and digital 
audio data input will be enabled.
5
Move the cursor to the DIGITAL PATCH IN 
field, and turn the [DATA/JOG] dial to select 
“1/2” (input channels 1/2) as the destination 
for the input signal from the DIGITAL STE-
REO IN jack.
6
Use the Quick Navigation section 
[RECORD] key to access the DIRECT page 
of the RECORD screen, and connect input 
channels 1/2 directly to tracks 1/2.
7
Raise the [STEREO] fader, play back your 
digital recorder, and check the recording 
level and monitor level.
8
When you are finished setting the levels, 
put the AW1600 in record mode, and play 
back your digital recorder.
• Please note that the EQ and dynamics settings you made for 
the stereo output channel during mixdown are still valid at this 
point. If necessary, turn off EQ and dynamics.
NOTE
Recording audio data from 
a digital recorder
AW1600
MONITOR
OUT
DIGITAL
STEREO IN
DIGITAL
STEREO OUT
Digital recorder 
(MD or DAT)
• If necessary, use the INIT page of the MONITOR screen to 
initialize the input channels.
NOTE
• If you want to lower the recording level, access the FADER 
page of the VIEW screen and lower the on-screen faders for 
input channels 1/2. (The [GAIN] knobs have no effect on input 
signals from the DIGITAL STEREO INPUT jack.)
NOTE