Yamaha aw1600 Manual De Usuario
Pairing input channels/track channels
5
Tr
ac
k recording
49
AW1600 Owner’s Manual
Pad tracks 1–4 and track channels 9/10–15/16 are permanently paired.
However, you may also specify pairing for adjacent odd-numbered/even-numbered input chan-
nels (1/2, 3/4, 5/6, 7/8) or track channels (1/2, 3/4, 5/6, 7/8). When two channels are paired, most
of their parameters will be linked, so that operating one of the channels will cause the same set-
ting to occur on the other channel as well.
This is convenient when you are recording a stereo audio source, or when you want to play back
two bus-recorded tracks as a single stereo track.
However, you may also specify pairing for adjacent odd-numbered/even-numbered input chan-
nels (1/2, 3/4, 5/6, 7/8) or track channels (1/2, 3/4, 5/6, 7/8). When two channels are paired, most
of their parameters will be linked, so that operating one of the channels will cause the same set-
ting to occur on the other channel as well.
This is convenient when you are recording a stereo audio source, or when you want to play back
two bus-recorded tracks as a single stereo track.
1
Hold down the [INPUT SEL] key (or [TRACK
SEL] key) of one channel that you want to
pair, and then press the other [INPUT SEL]
key (or [TRACK SEL] key).
SEL] key) of one channel that you want to
pair, and then press the other [INPUT SEL]
key (or [TRACK SEL] key).
A popup window will appear, asking you to confirm
the pairing.
the pairing.
2
Move the cursor to one of the following but-
tons and press the [ENTER] key.
tons and press the [ENTER] key.
• INPUT (TRACK) x
→ y
(x= odd number, y= even number)
...........Copy the settings of input (track) channel x
to y, and pair them.
• INPUT (TRACK) y
→ x
(x= odd number, y= even number)
...........Copy the settings of input (track) channel y
to x, and pair them.
• RESET BOTH
...........Initialize both input (track) channels, and
pair them.
• CANCEL
...........Cancel pairing.
When input channels are paired, all mix parameters
other than the [GAIN] knob and phase/pan settings
will be linked.
other than the [GAIN] knob and phase/pan settings
will be linked.
When track channels are paired, all mix parameters
other than the phase/pan settings will be paired. Oper-
ating just the odd-numbered fader will adjust the level
of both odd-numbered/even-numbered channels.
(While channels are paired, the even-numbered fader
has no effect.)
other than the phase/pan settings will be paired. Oper-
ating just the odd-numbered fader will adjust the level
of both odd-numbered/even-numbered channels.
(While channels are paired, the even-numbered fader
has no effect.)
3
To defeat pairing, hold down the [INPUT
SEL] key (or [TRACK SEL] key) of one of
the channels, and press the other [INPUT
SEL] key (or [TRACK SEL] key).
SEL] key (or [TRACK SEL] key) of one of
the channels, and press the other [INPUT
SEL] key (or [TRACK SEL] key).
A popup window will ask you to confirm that you
want to cancel pairing.
want to cancel pairing.
4
To cancel pairing, press the OK button. If
you decide not to cancel pairing, move the
cursor to the CANCEL button and press the
[ENTER] key.
you decide not to cancel pairing, move the
cursor to the CANCEL button and press the
[ENTER] key.
Pairing input channels/track channels
• In the case of paired channels, setting the pan to far left or far
right will produce nominal level. (The levels before and after
passing through Pan will be the same.) In the case of paired
channels, setting the pan to center will produce nominal level.
passing through Pan will be the same.) In the case of paired
channels, setting the pan to center will produce nominal level.
HINT