Panasonic SC-MAX370 Manual De Usuario

VQ

T5

K

74

• The pairing of the device has been replaced.

Do pairing again.

• This system might be connected to a different device.

Disconnect the other device and try pairing the device again.

The device is connected but audio cannot be heard 
through the system.
• For some built-in Bluetooth

®

 devices, you have to set 

the audio output to “SC-MAX370” manually. Read the 
operating instructions of the device for details.

Sound from the device is interrupted.
• The device is out of the 10 m communication range.

Move the device nearer to the system.

• Remove any obstacle between the system and the device.
• Other devices that use the 2.4 GHz frequency band (wireless router, 

microwaves, cordless phones, etc.) are interfering. Move the device 
nearer to the system and distance it from the other devices.

• Select “MODE 1” for stable communication.

The One-Touch Connection (NFC feature) is not working.
• Make sure the unit and the NFC feature of the device 

are turned on. (> 13)

“USB A NO DEVICE”
“USB B NO DEVICE”
• The USB device is not connected. Examine the connection.

“DEVICE FULL”
• You cannot do recording because the remaining recording time of 

the USB device is less than the total time of the music source.
Change to a USB device which has enough recording time and do 
the recording again.

“ERROR”
• An incorrect operation was done. Read the instructions and try again.

“ERROR” (during recording)
• You cannot select other playback source (example: 

radio, USB etc.) or press [:] or [9] during 
recording. Stop the recording function.

• You cannot open the disc tray when recording from an AM source.

“F61”
• Examine and correct the speaker cords connection.
• Disconnect the USB device. Switch off the system and 

then switch it on again.

“F70”
• Examine the Bluetooth

®

 device.

• Disconnect the Bluetooth

®

 device. Switch off the 

system and then switch it on again.

“F77”
• Switch off the system and then switch it on again.

“NO PLAY”
“UNSUPPORT”
• Examine the content. You can only play supported format.
• The files in the USB device can be corrupted. Format 

the USB device and try again.

• The unit may have a problem. Turn the unit off and then on again.

“NO TRACK”
• There is no album or track in the USB device or the internal memory.

“PLAYERROR”
• You played an unsupported MP3 file. The system will 

skip that track and play the next one.

“REMOTE 1”
“REMOTE 2”
• The remote control and the main unit are using different 

codes. Change the code of the remote control.
- When “REMOTE 1” is shown, press and hold [OK] 

and [1] for a minimum of 4 seconds.

- When “REMOTE 2” is shown, press and hold [OK] 

and [2] for a minimum of 4 seconds.

“TEMP NG”
• The temperature protection circuit has been activated, 

and the system will switch off. Let the unit cool down 
before switching it on again.

• Check that the ventilation opening of the unit is not obstructed.
• Ensure this unit is well ventilated.

“USB OVER CURRENT ERROR”
• The USB device is using too much power.

Disconnect the USB device, switch off the system and 
then switch on again.

“VBR”
• The system cannot show the remaining play time for 

variable bit rate (VBR) tracks.

Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.

While you press and hold [Í/I] on the main unit, 
connect the AC power supply cord again.
Continue to press and hold the button (approximately 
10 seconds) until “- - - - - - - -” is shown.

Release [Í/I].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.

When other Panasonic equipment responds to the 
remote control of this system, change the remote control 
code for this system.

Preparation
Press [RADIO/EXT-IN] to select “AUX 1” or “AUX 2”.

SC-MAX370PU_eng.book  18 ページ  ２０１４年３月６日　木曜日　午後２時５６分