ONKYO TX-NR901 Manual De Usuario
37
Connecting the TX-NR901
—Continued
The TX-NR901 has AC outlet(s) on its rear panel that
can be used to connect the power cords of AV compo-
nents that you intend to use with the TX-NR901. These
components can then be left turned on so that they turn
on and off as and when the TX-NR901 is turned on and
set to Standby.
can be used to connect the power cords of AV compo-
nents that you intend to use with the TX-NR901. These
components can then be left turned on so that they turn
on and off as and when the TX-NR901 is turned on and
set to Standby.
Caution:
• Make sure that the total capacity of the components
that you connect to the AC OUTLETS does not exceed
the stated capacity (e.g., TOTAL 120 W).
the stated capacity (e.g., TOTAL 120 W).
Note:
• Onkyo components with
sockets should be con-
nected to regular wall outlets.
• The number of AC OUTLETS, connector type, and
total capacity will depend on the country in which you
purchased the TX-NR901.
purchased the TX-NR901.
This port can be used to connect an external controller
for controlling the TX-NR901.
for controlling the TX-NR901.
Notes:
• Before connecting the power cord, connect all of your
speakers and AV components.
• Turning on the TX-NR901 may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the TX-NR901 into a different branch circuit.
equipment on the same circuit. If this is a problem,
plug the TX-NR901 into a different branch circuit.
The following notes don’t apply to the American and
Australian models:
Australian models:
• Do not use a power cord other than the one supplied
with the TX-NR901. The supplied power cord is
designed exclusively for use with the TX-NR901 and
should not be used with any other equipment.
designed exclusively for use with the TX-NR901 and
should not be used with any other equipment.
• Never disconnect the power cord from the TX-NR901
while the other end is still plugged into a wall outlet.
Doing so may cause an electric shock. Always discon-
nect the power cord from the wall outlet first, and then
the TX-NR901.
Doing so may cause an electric shock. Always discon-
nect the power cord from the wall outlet first, and then
the TX-NR901.
• The TX-NR901 is shipped with the POWER switch in
the ON position (
). When the power cord is con-
nected for the very first time, the TX-NR901 will enter
Standby and the STANDBY indicator will light up.
Standby and the STANDBY indicator will light up.
• To completely shutdown the TX-NR901, set the
POWER switch to the OFF position (
).
Connecting the Power Cords of Other
Components
Components
Connecting the RS232 Port
AC OUTLETS
AC 120 V 60 Hz
SWITCHED
TOTAL 120W 1A MAX.
AC OUTLETS
AC 230-240 V 50 Hz
SWITCHED
TOTAL 100 W MAX.
European and some
Asian models
Asian models
American model
Connecting the Power Cord
1
Connect the supplied power cord
to the TX-NR901’s AC INLET.
to the TX-NR901’s AC INLET.
(Skip this step if you have the American
model.)
model.)
2
Plug the power cord into an AC
wall outlet.
wall outlet.
The STANDBY indicator lights up.
On models with a POWER switch, the
STANDBY indicator comes on only if
that switch is in the ON position (
STANDBY indicator comes on only if
that switch is in the ON position (
).
TX-NR901_En.book Page 37 Wednesday, October 1, 2003 9:44 AM