GE DCVH680EJBB Manual De Usuario

or Visit our Web site at:  www.GEAppliances.com (US)

Step 1 Prepare the Area and Exhaust for Installation of New

Dryer (see section 1).

Step 2 Check and Ensure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation
Specifications (see section 3).

Step 3 Remove the Foam Shipping Pads (see section 1).
Step 4 Move the Dryer to the Desired Location.
Step 5 Connect the Power Supply (see section 2).
Step 6 Connect the External Exhaust (see section 4).
Step 7 Level Your Dryer (see section 5).

Step 8 Check the Operation of the Power Supply and

Venting.

Step 9 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be
Noticed By the Owner.

For Alcove or Closet Installation, see section 6.
For Bathroom or Bedroom Installation, see section 7.
For Mobile or Manufactured Home see, section 8.
For side or bottom exhaust, see section 9.

500A436P009_Rev0

Pub # 31-16228

Save these instructions for local   
inspector’s use.

Observe all governing codes and     

ordinances.  

• Note to Installer - Be sure to leave these instructions with  

the customer.

• Note to Customer - Keep these instructions with your Use  

and Care Book for future reference. 

• Before the old dryer is removed from service or discarded,  

remove the dryer door.

• Service information and the wiring diagram are located in   

the control console. 

• Do not allow children on or in the appliance.  Close super- 

vision of children is necessary when the appliance is used  
near children. 

• Install the dryer where the temperature is above 50°F for 

satisfactory operation of the dryer control system.

GLOVES

SAFETY

GLASSES

DRYER POWER CORD

KIT (NOT PROVIDED

WITH DRYER)

4" DUCT

CLAMPS (2)

OR

4" SPRING

CLAMPS (2)

EXHAUST

HOOD

3/4" STRAIN

RELIEF

UL RECOGNIZED

4" DIA. METAL

ELBOW

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

 KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

DUCT TAPE

UL RATED 

120/240V,30A       

WITH 3 OR 4 PRONGS. 

IDENTIFY THE PLUG 

TYPE AS PER THE 

HOUSE RECEPTACLE 

BEFORE PURCHASING 

LINE CORD. 

SLIP JOINT PLIERS

FLAT BLADE SCREWDRIVER

PHILLIPS SCREWDRIVER

LEVEL

 

•  To reduce the risk of severe injury or death, follow all installation instructions.
•  Clothes dryer installation must be performed by a qualified installer.
•  Install the clothes dryer according to these instructions and in accordance 

with local codes.

•  This dryer must be exhausted to the outdoors.
•  Use only 4” rigid metal ducting for exhausting the clothes dryer to the 

outdoors.

•  Do not install or store this appliance in any location where it could be 

exposed to water and or weather.

•  Save these instructions.  (Installers: Be sure to leave these instructions with 

the customer).

•  DO NOT install a clothes dryer with flexible plastic ducting materials.

If flexible metal (semi-rigid or foil-type) duct is installed, it must be UL listed 

and installed in accordance with the instructions found in "Connecting The 

Dryer To House Vent" on page 5 of this manual.  Flexible venting materials 

are known to collapse, be easily crushed, and trap lint.  These conditions will 

obstruct dryer airflow and increase the risk of fire.