Sharp LC-32L400X Manual De Usuario

[ 3hr.]

No operation off

Ecology

Option

Power management

4

Setup

[ Enable]

No signal off

ECO

H No signal off
You can set the TV to automatically power off in about 
15 minutes after the TV goes into a state of receiving 
no programme signals, such as the end of a broadcast 
day. (Enable, Disable)

• Five minutes before the power shuts down, the remaining 

time displays every minute.

• “Disable” is the factory preset value.
• When a TV programme fi nishes, and the TV receives signal 

input, this function may not operate.

H Power management (PC input mode only)
You can set the TV to automatically power off when no
image is displayed on PC.

• No power management 
• Factory preset value.

• If no signal inputs for approximately

8 minutes, the power shuts down.

• Even if you start using the PC and the 

signal inputs again, the TV stays off.

• The TV turns on again by pressing 

POWER. (See page 7.)

• If no signal inputs for approximately

8 seconds, the power shuts down.

• When you start using the PC and the 

signal inputs again, the TV turns on.

• The TV turns on again by pressing 

POWER. (See page 7.)

H No operation off
You can set the TV to automatically power off when no 
TV operation is performed for more than 3 hours.
(30 min., 3 hr., Disable)

• Five minutes before the power shuts down, the remaining 

time displays every minute.

• “Disable” is the factory preset value.

H Ecology
When set to “Yes”, the TV activates the following 
power saving mode.

• “OPC” set to “On” (Page 11)
• “No signal off” set to “Enable” (Page  12)
• “Power management” set to “Mode1” (Page 12)
• “No operation off” set to “3 hr.” (Page 12)
• “Quick start” set to “Off” (Page 14).

• Ecology mode cannot be deactivated by selecting “No”. 

Each setting must be changed individually to deactivate 
Ecology mode.

Auto installation

Analogue programme setup

Digital programme setup

Input skip

Input label

4

4

Position

4

Text language

Identification

Reset

[ On]

[ Panorama]

[ Off]

[ West Europe]

Setup

Option

HDMI auto view

WSS

4:3 mode

Quick start

Child lock

Digital setup

H Child lock (ATV and DTV input mode only)
Allows you to use a password to protect certain 
settings from being accidentally changed.

Repeat steps 1 to 2 in Menu operation.

Press 

a/b to select “Child lock”, and then 

press ENTER. 

If you already set the password, enter it here.

Press 

a/b to select “Change password”, and 

then press ENTER.

Enter the 4-digit number as a password using 
0 — 9.

New password

–  –  –  –

Reconfirm

Change password

Clear password

Parental rating

– 

 –  –  –

Enter your new password. Use 4 digits

Enter the same 4-digit number as in step 5 to 
confi rm.

• To view a locked channel (Lock setting in Analogue 

programme setup “Manual adjust” is set to “On”), you must 
enter a password. When you select a locked channel, “Child 
lock has been activated” is displayed.

• Press ENTER to display the password input window.

Clearing the password
Allow you to clear your password.

Repeat steps 1 to 3 in Setting a password.

Press 

a/b to select “Clear password”, and 

then press ENTER. 

Press 

c/d to select “Yes”, and then press 

ENTER. 

LC32L400X_EN.indb   12

LC32L400X_EN.indb   12

7/8/10   6:45:14 PM

7/8/10   6:45:14 PM