MB Quart ONX2.100 Manual De Usuario

 MODE: “5” since 3 sets of RCA’s are connected.

You can use this configuration simply as 4 discrete full range channels, with a 5th low 
pass channel. All of the crossovers are bypassed , except the LOW PASS on channel 5.

Control checklist:
- Refer to the section “Settings for Best Performance”

Interconnect cable checklist:
Connect channel 1&2 inputs to the front output, channels 3&4 to the rear output, and 

channel 5 to the mono subwoofer output of a head unit or in dash equalizer.

Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4  X-OVER: FULL

 MODE: “2” since 1 set of RCA’s are connected.

We will use the same basic setup on the speaker and subwoofer connections as above 
to illustrate an installation that only has 1 set of stereo RCA’s to connect to this amplifier. 

By switching the amplifier to 2CH on the INPUT MODE, you now provide signal to all 

- Refer to the section “Settings for Best Performance”

channels on the amplifier. You sacrifice the ability to fade front to rear though.

Connect Stereo Left and Right RCA’s from headunit to CH1&2 RCA Inputs.

Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4  X-OVER: FULL

FEATURES:
- 3 Sets of RCA inputs
- LEVEL: Variable sensitivity from 0.2V to 6V
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 10dB
- X-OVER: Selects internal crossover functions
   - FULL: Bypasses all crossovers for full frequency operation
   - BP: Selects the built in LOW PASS filter, variable from 30Hz to 150Hz
   - HI: Selects the built in HI PASS filter, variable from 10Hz to 15KHz

- POWER LED: Indicates the powered up and turned on condition
- PROTECTION LED: Indicates a high voltage, low voltage, short circuit,
  hard clip, over heating or DC fault condition.
- MODE: “2” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 and 5 through
  1/2 inputs. “4” indicates connecting 2 sets of RCA’s to 1/2 and 3/4 inputs. “5” indicates connecting 3 sets of
  RCA’s to channels 1/2, 3/4 and mono signal to channel 5 inputs.

REMOTE

POWER

PROTECT

CH2

CH1

CH4

CH3

5CH

10Hz  15Khz

  10Hz 15Khz

HI P
ASS

6V      0.2V

LEVEL

6V   0.2V

LEVEL

LOW P
ASS

30Hz 150Hz

HI P
ASS

MODE

Ch2  Ch4  

Ch5

X-OVER  CH3/4

0dB-10dB

30Hz 150Hz

6V   0.2V

BASS EQ

LOW P
ASS

LEVEL

HI   FULL

HI FULL BP

X-OVER CH1/2

REMOTE

POWER

PROTECT

CH2

CH1

CH4

CH3

5CH

10Hz  15Khz

  10Hz 15Khz

HI P
ASS

6V      0.2V

LEVEL

6V   0.2V

LEVEL

LOW P
ASS

30Hz 150Hz

HI P
ASS

MODE

Ch2  Ch4  Ch5

X-OVER  CH3/4

0dB-10dB

30Hz 150Hz

6V   0.2V

BASS EQ

LOW P
ASS

LEVEL

HI   FULL

HI FULL BP

X-OVER CH1/2

REMOTE

PROTECT

POWER

CH2

CH1

CH4

CH3

5CH

10Hz  15Khz

  10Hz 15Khz

HI PASS

6V      0.2V

LEVEL

6V   0.2V

LEVEL

LOW PASS

30Hz 150Hz

HI PASS

MODE

Ch2  Ch4  Ch5

X-OVER

 CH3/4

0dB-10dB

30Hz 150Hz

6V   0.2V

BASS EQ

LOW PASS

LEVEL

HI   FULL

HI FULL BP

X-OVER

CH1/2