Great Dane GDB10030 Manual De Usuario
Assembly - 33
ASSEMBLY
Assembly
Bag of Parts
Check Engine Oil Level
Remove dipstick from tube by unscrewing it. Wipe it clean.
9. Install dipstick and allow the cap to rest on the end of the
tube. Do not tighten the cap.
tube. Do not tighten the cap.
10.Remove dipstick. Check oil level on dipstick; oil level
should be between the ADD and FULL marks.
should be between the ADD and FULL marks.
•
If oil is low, add oil to bring oil level no higher than the
FULL mark on dipstick.
•
If oil level is above the FULL mark, drain to proper
level.
11.Install and tighten dipstick.
Check Tire Pressure
1. Check tires for damage.
2. Check tire pressure with an accurate gauge.
3. Check that tires have correct pressure. Add air, if
necessary:
necessary:
Lubricate Machine
Lubricate all moving parts before operating the machine.
See Lubrication Points in the Service Lubrication section.
See Lubrication Points in the Service Lubrication section.
Check Mower Deck Level
The mower deck is assembled and adjusted at the factory.
After machine is completely assembled, check the mower
front-to-rear and side-to-side deck level.
After machine is completely assembled, check the mower
front-to-rear and side-to-side deck level.
Check Safety System
For a complete checkout procedure of the safety interlock
system, see Testing the Safety Interlock System in the
Operating section.
system, see Testing the Safety Interlock System in the
Operating section.
Initial Adjustments
1. Check free-wheel valves on transaxle assemblies to
make sure that the valves are closed.
make sure that the valves are closed.
2. Raise the rear of the machine until the drive wheels are
off the ground. Support the machine with jackstands.
off the ground. Support the machine with jackstands.
3. Start and run the engine until it reaches normal
operating temperature.
operating temperature.
4. Move speed control lever to the forward position, lower
Qty.
Description
1
Key
1
Operator’s Manual
1
PDR Check List
c
CAUTION: Avoid injury! Explosive separation of
a tire and rim parts can cause serious injury or
death:
death:
• DO NOT attempt to mount a tire without the
proper equipment and experience to perform
the job.
proper equipment and experience to perform
the job.
• Always maintain the correct tire pressure. DO
NOT inflate the tires above the recommended
pressure. Never weld or heat a wheel and tire
assembly. The heat can cause an increase in
air pressure resulting in a tire explosion.
Welding can structurally weaken or deform the
wheel.
NOT inflate the tires above the recommended
pressure. Never weld or heat a wheel and tire
assembly. The heat can cause an increase in
air pressure resulting in a tire explosion.
Welding can structurally weaken or deform the
wheel.
• When inflating tires, use a clip-on chuck and
extension hose long enough to allow you to
stand to one side and NOT in front of or over
the tire assembly.
extension hose long enough to allow you to
stand to one side and NOT in front of or over
the tire assembly.
• Check tires for low pressure, cuts, bubbles,
damaged rims or missing lug bolts and nuts.
damaged rims or missing lug bolts and nuts.
Tire Size
Pressure
Front: 9 x 3.5-4
172
-
207kPa (25
-
30 psi)
Rear: 16 x 6.5-8
69
-
83kPa (10
-
12 psi)
c
CAUTION: Avoid injury! Clear area of
bystanders before performing this service
procedure.
procedure.
c
CAUTION: Avoid injury! Engine exhaust fumes
contain carbon monoxide and can cause
serious illness or death.
serious illness or death.
Move the vehicle to an outside area before
running the engine.
running the engine.
Do not run an engine in an enclosed area
without adequate ventilation.
without adequate ventilation.
•
Connect a pipe extension to the engine
exhaust pipe to direct the exhaust fumes out of
the area.
the area.
•
Allow fresh outside air into the work area to
clear the exhaust fumes out.