Dixon ZTR 428 D 429 Manual De Usuario

             TECHNICAL DATA BROCHURE - ZTR 428 d 429                                 

Page 1

 

IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS

 

Deluxe Seat Adjustment

 

Easy hand lever action allows forward and backward movement of seat.  No bolts to loosen  or 

tighten.

 

Mower Blade Operation

 

1.  To start mower blades, pull up slightly on blade drive switch handle and move it

 

forward to the "ON" position.  2.  To stop mower blades, move switch 
handle to the "OFF" position.

 

Body Removal

 

1.  Disconnect throttle cable from engine.

 

2.  Disconnect rear wiring loom from the body by turning the threaded collar on connector, in a 

counterclockwise direction. This plug is located at the right rear of body.

 

3.  Remove the four control lever bolts and remo ve upper control levers (P/N 9079 & 9080).

 

4.  Remove the two acorn nuts on floor of body and release latches on the rear of body

 

near each side.   

5.  Place height adjustment lever in the vertical position, engage the parking brake and

 

carefully lift body off the chassis.   

6.  Reverse above procedures to install body.

 

Safety Checks - "IMPORTANT"

 

1.

  After reassembly of body onto chassis and while seated on the mower, attempt to start the 

engine with mower deck engaged. The engine should not start. If engine do es start, return mower 
to an Authori zed Dixon Dealer for adjustment or repair.  

2.  Disengage mower deck and start engine with the operator in a normal seated position  on the 

mower. Engage mower deck and remove weight from the seat. The engine should  stop. If engine 
does not stop when operator rises from seat, return mower to an  Authorized Dixon Dealer for 
adjustment or repair.

 

Parking Brake Adjustment

 

1.  Remove body as described above.

 

2.    Adjustment points are located at rear of transaxle 'on each side. 

Remove roll pins 

from swivel fitting (P/N 2172). Turn swivel fitting on brake rod (P/N 5100) in to 
tighten, just enough to prevent brake from slipping when engaged.

 

3.  Reinstall roll pin.

 

CAUTION: Over tightening may cause premature wear on brake band (P/ N 5085).

 

Mower Deck Drive Adjustment

 

No adjustment necessary! The spring loaded idler pulley maintains proper tension throughout  

belt life.

 

Removing Mower Deck

 

1.  Remove mower deck drive belt (P/N 6111) by  p u l l i n g  idler pulley (P/N 1687) away from  belt and 

remove belt from the rear pulley.

 

2.  Remove the two clevis pins (P/N 3072) from the L -rods at rear of deck and slide free  from 

slots.

 

3.  Remove the clevis pin (P/N 3072) from the lift linkage at the front of deck.

 

4.  Remove cotter pin from shaft (P/N  1332) located at front of mower deck on slide  

plates welded at battery box. Slide shaft free.

 

5.  Raise front of mower and roll it free of mower deck assembly.

 

6.  To install deck, reverse above procedure.

 

Removing Mower Blade

 

1.  Secure mower blade (P/N 6 231) from turning.

 

2.  Observe blade position when removing.

 

3.  Remove blade bolt (P/N 3268), lock washer (P/N 3065) and blade washer (P/N 6113).

 

4.  To reinstall, reverse above procedure.

 

WARNING:  Sharp edges on blade can cause injury; Caution should be  exercised when  

    service is required on the blade.

 

(P/N 8604)

 

 

  

DIXON INDUSTRIES, INC.

 

«