Roland XV-5080. Manual De Usuario
106
Chapter 2 Using the XV-5080 Effects
Copying Effect Settings
You can copy the effect settings from any Patch,
Performance, or Rhythm Set into the currently selected
Patch, Performance, or Rhythm Set. This can save a great
deal of time and effort when setting up effects.
Performance, or Rhythm Set into the currently selected
Patch, Performance, or Rhythm Set. This can save a great
deal of time and effort when setting up effects.
You can select the following effect contents to be copied.
Copy Type
ALL:
Multi-effects, Chorus, and Reverb settings
MFX:
Multi-effects settings in the General page
CHORUS:
Chorus settings
REVERB:
Reverb settings
CHO&REV:
Chorus and Reverb settings
* If the copy source is a Performance, the contents copied for
“MFX” will be the Multi-effects settings for the Performance
itself (the Multi-effects setting when MFX 1–3 Source is set to
“PERFORM” in the General page). When the MFX settings
such as patches is copied to the Performance, the data will be
copied as the Multi-effects settings for the Performance itself.
itself (the Multi-effects setting when MFX 1–3 Source is set to
“PERFORM” in the General page). When the MFX settings
such as patches is copied to the Performance, the data will be
copied as the Multi-effects settings for the Performance itself.
1. Make sure the Patch, Performance or Rhythm Set is
selected.
2. Press [SYSTEM/UTILITY] several times, getting its
indicator to start blinking.
The Utility Menu page appears.
fig.02-032.e_70
* When the indicator lights, you are in SYSTEM mode. In this
case, press [SYSTEM/UTILITY] once again to get its
indicator to start blinking.
indicator to start blinking.
3. Press [F2 (Copy)].
4. Press [
] to move the cursor to Type, then select
EFFECT.
The corresponding Effect Copy page will appear.
fig.02-033.e_70
Destination “Temporary” indicates that the copy destination
is the currently selected Patch, Performance, or Rhythm Set.
is the currently selected Patch, Performance, or Rhythm Set.
5. Press [
]/[
]/[
]/[
] to move the cursor to
the parameter you want to set.
6. Turn the VALUE dial or press [INC]/[DEC] to select the
desired value.
7. Press [F6 (Copy)] to execute the copy.
8. Press [EXIT] to return to the Play page.
When Using 3D Effects
The following 3D effects utilize RSS (Roland Sound
Space) technology to create a spaciousness that cannot be
produced by delay, reverb, chorus, etc.
Space) technology to create a spaciousness that cannot be
produced by delay, reverb, chorus, etc.
48: 3D DELAY
60: 3D CHORUS
61: 3D FLANGER
70: 3D DELAY 2
89: 3D AUTO SPIN
90: 3D MANUAL
When using these effects, we recommend that you place
your speakers as follows. Also, make sure that the
speakers are at a sufficient distance from the walls on
either side.
your speakers as follows. Also, make sure that the
speakers are at a sufficient distance from the walls on
either side.
fig.02-031.e
If the left and right speakers are too far apart, or if there
is too much reverberation, the full 3D effect may not
appear.
is too much reverberation, the full 3D effect may not
appear.
Each of these effects has an Out (Output Mode)
parameter. If the sound from the OUTPUT jacks is to be
heard through speakers, set this parameter to “Speaker.”
If the sound is to be heard through headphones, set it to
“Phones.” This will ensure that the optimal 3D effect will
be heard. If this parameter is not set correctly, the full 3D
effect may not appear.
parameter. If the sound from the OUTPUT jacks is to be
heard through speakers, set this parameter to “Speaker.”
If the sound is to be heard through headphones, set it to
“Phones.” This will ensure that the optimal 3D effect will
be heard. If this parameter is not set correctly, the full 3D
effect may not appear.
30˚
30˚