Roland XV-5080. Manual De Usuario
32
Chapter 2 Using the XV-5080 Effects
* When you press [F2 (MFX)] once again, the MFX Param page
will reappear.
MFXA–C Control 1–4 Source
Select the Control Source to be used for changing the Multi-
effects parameters, and set the Sens and parameters to be
changed by that Control Source.
effects parameters, and set the Sens and parameters to be
changed by that Control Source.
OFF:
No controller is used.
CC01–95:
Controller numbers 1–95 (except for 32)
PITCH BEND:
Pitch Bend
AFTERTOUCH:
Aftertouch
SYS-CTRL 1–4:
System control 1–4
MFXA–C Control Destination 1–4
Selects the Multi-effects parameter to be controlled using the
MFX Control 1–4 source. The parameters that can be selected
depend on which type of Multi-effects is set to MFX Type.
MFX Control 1–4 source. The parameters that can be selected
depend on which type of Multi-effects is set to MFX Type.
MFXA–C Control 1–4 Sens -63– +63
If you wish to modify the selected parameter in a positive (+)
direction—i.e., a higher value, toward the right, or faster,
etc.—from its current setting, select a positive (+) value. If
you wish to modify the selected parameter in a negative (-)
direction—i.e., a lower value, toward the left, or slower,
etc.—from its current setting, select a negative (-) value.
Higher numbers produce a greater amount of change.
direction—i.e., a higher value, toward the right, or faster,
etc.—from its current setting, select a positive (+) value. If
you wish to modify the selected parameter in a negative (-)
direction—i.e., a lower value, toward the left, or slower,
etc.—from its current setting, select a negative (-) value.
Higher numbers produce a greater amount of change.
Making Chorus Settings
The XV-5080’s Chorus effect unit can also be used as a stereo
delay unit.
delay unit.
These settings allow you to select chorus or delay, the
characteristics of the selected effect type, and the Chorus
output routing.
characteristics of the selected effect type, and the Chorus
output routing.
On the Effects General page, set the following parameters.
Chorus Type
0 (Off):
Neither Chorus or Delay is used.
1 (Chrus):
Chorus is used.
2 (Delay):
Delay is used.
Chorus Source PRF/P1–32
Set this when assigning chorus settings that are used by
another part. Select PRF when using the Performance's
chorus settings. When using the chorus settings assigned to
one of the parts, select the part number (P1–32).
another part. Select PRF when using the Performance's
chorus settings. When using the chorus settings assigned to
one of the parts, select the part number (P1–32).
Chorus Output Select
This parameter allows you to send the Chorus output
directly to the currently selected OUTPUT jacks, to the
Reverb, or to both.
directly to the currently selected OUTPUT jacks, to the
Reverb, or to both.
MAIN:
The Chorus output is sent only to the OUTPUT jacks.
fig.02-019.e
REV:
The Chorus output is sent only to the Reverb.
fig.02-020.e
M+R:
The Chorus output is sent to the OUTPUT jacks and to
the Reverb.
fig.02-021.e
Chorus Level 0–127
Determines the Chorus output level.
Chorus Output Assign A–D
Selects the pair of OUTPUT jacks to which the Chorus unit’s
stereo output is routed when Chorus Output Select is set to
“MAIN” or “M+R.”
stereo output is routed when Chorus Output Select is set to
“MAIN” or “M+R.”
OUTPUT
OUTPUT
Chorus Input
Chorus
Reverb
OUTPUT
OUTPUT
Chorus Input
Reverb Input
Chorus
Reverb