Roland JUNO-G Manual De Usuario
99
Editing a Song (MIDI Track)
This function inserts blank measures into a specified song position.
As you can set the time signature of the blank measures, this is
convenient when inserting a phrase having a different time signature
in the middle of a song.
As you can set the time signature of the blank measures, this is
convenient when inserting a phrase having a different time signature
in the middle of a song.
*
Blank measures will also be inserted into the tempo track, beat track,
and audio tracks at the same time.
and audio tracks at the same time.
This transposes the pitch of notes within a specified area, over a +/-
127 semitone range. Use this function to modulate from one key to
another in a song, or to transpose the entire song.
127 semitone range. Use this function to modulate from one key to
another in a song, or to transpose the entire song.
Micro Edit lets you edit individual items of sequencer data recorded
in a song, such as MIDI messages and tempo data.
in a song, such as MIDI messages and tempo data.
*
When you’re going to edit a song, you have to first load it into the
Temporary Area (p. 94).
Temporary Area (p. 94).
Access the Microscope screen when you want to view the sequencer
data recorded in a song. Each line indicates the location (measure-
beat-tick) at which the sequencer data is recorded, and the data
recorded at that location.
data recorded in a song. Each line indicates the location (measure-
beat-tick) at which the sequencer data is recorded, and the data
recorded at that location.
1.
Load the song that contains the sequencer data you want to
2.
Press [F3 (MICRO)].
The MICROSCOPE screen appears.
Press [
] [
] to view sequencer data.
*
Each time you press [F6 (VIEW)] you will switch between the two
screens. (Piano Roll
screens. (Piano Roll
↔
Event List)
Inserting a Blank Measure (Insert)
Parameter
Value
Explanation
Measure
0001–END
Measure location at which the blank
measures are to be inserted
measures are to be inserted
For
1–
Number of blank measures to be insert-
ed
ed
Beat
Numerator: 1–32
Denominator: 2,
4, 8, 16
Denominator: 2,
4, 8, 16
In general, the time signature of the
measure immediately before insertion
will be used for the blank measures. To
change the time signature of the blank
measures to be inserted, use this pa-
rameter.
measure immediately before insertion
will be used for the blank measures. To
change the time signature of the blank
measures to be inserted, use this pa-
rameter.
* Beat can be specified only when you have
set “Track” to “TRK ALL.”
Transpose the Key (Transpose)
Parameter
Value
Explanation
Ch/Part
ALL, Ch 1–16
MIDI channel(s) of the notes to be trans-
posed
posed
ALL:
Transposes all notes.
Ch 1–16:
Transposes only the notes of a specific MIDI
channel.
Measure
0001–
Range of measures to be transposed
If you set “For” to “ALL,” all mea-
sures will be specified.
sures will be specified.
For
1–ALL
Range Min
0 (C -)–127 (G9)
Range of note numbers to be transposed
You can also specify the key range by
pressing keys on the keyboard.
pressing keys on the keyboard.
Range Max
Bias
-127– +127
Transpose amount in semitone steps
Set a “+” (positive) value to raise the
pitch, or a “-” (negative) value to low-
er the pitch.
pitch, or a “-” (negative) value to low-
er the pitch.
Editing Individual Items of
Sequencer Data (Micro Edit)
Sequencer Data (Micro Edit)
Editing Sequencer Data (Basic
Procedure in the Microscope)
Procedure in the Microscope)
If You Want to Lower the Bass Sound One
Octave...
Octave...
If your bass is played one octave higher than the staff notation,
use the Transpose function to lower it one octave.
To lower the bass sound one octave, set the Range parameter to
“Lowest-Highest” for the bass part, and set the Bias parameter
to “-12.”
use the Transpose function to lower it one octave.
To lower the bass sound one octave, set the Range parameter to
“Lowest-Highest” for the bass part, and set the Bias parameter
to “-12.”
When You Want to Change Percussion
Sounds...
Sounds...
You can also use the Transpose function to change percussion
sounds.
Suppose you want to change conga to tom. If the conga sound is
assigned to the D4 key, and the tom sound is assigned to the C3
key, set the Range parameter to “D4–D4” and the Bias
parameter to “-14.”
sounds.
Suppose you want to change conga to tom. If the conga sound is
assigned to the D4 key, and the tom sound is assigned to the C3
key, set the Range parameter to “D4–D4” and the Bias
parameter to “-14.”
Location of the sequencer data (measure-beat-tick)
MIDI channel
Displays the parameter data at the cursor location
Sequencer data
JUNO-G_e.book 99 ページ 2006年2月13日 月曜日 午後2時44分