Pelco C586M Manual De Usuario
Pelco Manual C586M (9/99)
25
3.
Press the VIEW key for approximately three seconds. The basic System Setup menu
appears (refer to Figure 8).
appears (refer to Figure 8).
4.
The currently selected menu item blinks. Use the joystick to highlight ADVANCED
SETUP.
SETUP.
5.
Press the OPEN key. The Advanced System Setup menu appears (refer to Figure 9).
6.
Use the joystick to move between items on the screen. When the menu item you
desire is highlighted (blinking), press the OPEN key to cycle through the options.
desire is highlighted (blinking), press the OPEN key to cycle through the options.
Date Format
Sets the format for displaying the date on the main monitor.
Sets the format for displaying the date on the main monitor.
Password
Enables or disables password control to access programming menus.
Enables or disables password control to access programming menus.
Front Panel Control
Enables or disables the front panel buttons to operate the multiplexer. In either mode
you can access programming menus. Has no effect on the keyboard.
Enables or disables the front panel buttons to operate the multiplexer. In either mode
you can access programming menus. Has no effect on the keyboard.
Main Monitor Display
Select ALARMS, ACTIVITY, or ALARMS/ACTIVITY if you want the main monitor to
switch to cameras that have alarms or activity detection. If you are using the main
monitor for normal video and you do not want alarms or activity detection to override
what you are observing, select NONE.
Select ALARMS, ACTIVITY, or ALARMS/ACTIVITY if you want the main monitor to
switch to cameras that have alarms or activity detection. If you are using the main
monitor for normal video and you do not want alarms or activity detection to override
what you are observing, select NONE.
Spot Monitor Display
If you want the spot monitor to switch to cameras that have alarms or activity
detection, select BLANK, SEQUENCE, or TRACK MAIN, then under RESPONDS TO
select ALARMS, ACTIVITY, or ALARMS/ACTIVITY. If you are using the spot monitor
for normal video and you do not want alarms or activity detection to override what you
are observing, select NONE.
If you want the spot monitor to switch to cameras that have alarms or activity
detection, select BLANK, SEQUENCE, or TRACK MAIN, then under RESPONDS TO
select ALARMS, ACTIVITY, or ALARMS/ACTIVITY. If you are using the spot monitor
for normal video and you do not want alarms or activity detection to override what you
are observing, select NONE.
BLANK - Allows you to view an individual camera, but you cannot run a sequence. An
alarm or activity detection will override the camera you are viewing. When the alarm or
activity detection goes away, the screen will return to the camera you were viewing.
alarm or activity detection will override the camera you are viewing. When the alarm or
activity detection goes away, the screen will return to the camera you were viewing.
Figure 9. Advanced System Setup Menu
ALL COLOR*
COLOR & B/W
RESERVED
COLOR & B/W
RESERVED
DATE FORMAT
MM-DD-YY
PASSWORD DISABLED
FRONT PANEL CONTROL ENABLED
FRONT PANEL CONTROL ENABLED
MAIN MONITOR DISPLAY
RESPONDS TO
RESPONDS TO
NONE
SPOT MONITOR DISPLAY SEQUENCE
RESPONDS TO
RESPONDS TO
ALARMS
AUX MONITOR DISPLAY
BLANK
RESPONDS TO
ACTIVITY
CAMERA TYPES
ALL COLOR
UNIT ID
001
COMM. TYPE
MASTER (KBD-T/D)
RELAY OUTPUT
ALARM
MASTER (KBD-T/D)** (1)
SLAVE
SLAVE
(2)
001–240
SEQUENCE
BLANK
TRACK MAIN
BLANK
TRACK MAIN
*
ALL B/W SHOWN ON MONOCHROME MODELS.
(1) SIMPLEX DEFAULT SETTING
** MUST BE SET IN THIS MODE FROM THE FRONT PANEL OF THE
(2) DUPLEX DEFAULT SETTING
MULTIPLEXER TO PROGRAM THE MULTIPLEXER FROM THE KEYBOARD.
*** DUPLEX MULTIPLEXER ONLY; NOT ON SIMPLEX
BLANK
CAM 1
CAM 1
CAM 16
SEQUENCE
SEQUENCE
***
***
***