Manualsbrain.com
  1. Manuales
  2. Marcas
  3. Roland
  4. MC-09
  5. Manual De Usuario

Roland MC-09 Manual De Usuario

Descargar
Página de 88
59
Using a memory card
Saving a loop to a memory 
card
The loops recorded in the audio looper can be saved on a 
memory card. Here we will explain how to save individual 
loops of the specified part.
1. Press the [SETUP] button.
2. Press the [INC] or [DEC] button until the display 
indicates “
”.
3. Press the [ENTER] button.
The display will show the save-destination file number (L01– 
L50).
4. Press one of the audio looper [SEL] buttons to specify 
the part that you want to save.
5. Use the [INC] and [DEC] buttons to select the save-
destination file number.
* Should you decide that you don’t want to carry out the save, 
press the [SETUP] button or the [EXIT] button.
6. Press the [WRITE] button to begin saving the data.
While the data is being saved, “
” will appear in the 
display. When saving is complete, you’re returned to where 
you were in step 2.
 * If the save-destination file number already exists on the 
memory card, the display will indicate “
”. If you 
want to save the new data by overwriting the old, press the 
[ENTER] button. If you want to save the data with a different 
file number, press the [EXIT] button and repeat the 
procedure from step 2.
* It may take up to three minutes for saving one loop.
7. Press the [SETUP] button.
When you save a loop to a memory card, it is saved in the 
MC-09’s own original format. This means that loops you 
create on the MC-09 cannot be loaded or used by a personal 
computer or hard disk recorder. If you want to use an MC-09 
loop on a different device, you will have to record the loop 
onto that device as an audio signal.
Loading a loop
Here’s how to load a loop from a memory card into the audio 
looper.
1. Press the [SETUP] button.
2. Press the [INC] or [DEC] button until the display 
indicates “
”.
3. Press the [ENTER] button.
The display will show one of the file numbers (L01– L50) that 
have been saved on the memory card.
4. Press one of the audio looper [SEL] buttons to select the 
part into which the data will be loaded.
5. Use the [INC] and [DEC] buttons to select the load-
source file number.
* If you decide you don’t want to load a file, press the [SETUP] 
button or the [EXIT] button.
6. Press the [WRITE] button to begin loading.
The display will show “
” while the data is being 
loaded. When loading is finished, you’re returned to where 
you were in step 2.
* If a loop already exists in the load-destination part, the display 
will indicate “
”. If it is ok to overwrite this existing 
data when you load, press the [ENTER] button. If you decide 
to load the data into a different part, press the [EXIT] button 
and repeat the procedure from step 2.
* It may take up to three minutes for loading one loop.
7. Press the [SETUP] button.
Deleting a saved loop from 
memory card
Here’s how to delete a saved loop from memory card.
1. Press the [SETUP] button.
2. Press the [INC] or [DEC] button until the display 
indicates “
”.
3. Press the [ENTER] button.
The display will show one of the file numbers (L01– L50) that 
have been saved on the memory card.
4. Use the [INC] and [DEC] buttons to select the number 
of the file that you want to delete.
5. Press the [WRITE] button.
The display will indicate “
”, asking you to confirm 
the operation.
* If you decide not to delete the loop, press the [SETUP] button 
or the [EXIT] button.
6. Press the [ENTER] button to delete the loop.
While the loop is being deleted, the display will show 
“
”. When the loop has been deleted, you’re 
returned to where you were in step 2.
7. Press the [SETUP] button.