Akai MPK88 Manual De Usuario
37
PROGRAM CHANGE MODE
A Program Change, often referred to as a Patch Change, is a MIDI message used for sending data to
devices to cause them to change to a new program. This allows you to tell a hardware or software device
which sound to play. For example, if your MPK61/MPK88 is controlling a piano patch on your DAW or an
external device, using a Program Change command allows you to easily switch to a synth patch.
devices to cause them to change to a new program. This allows you to tell a hardware or software device
which sound to play. For example, if your MPK61/MPK88 is controlling a piano patch on your DAW or an
external device, using a Program Change command allows you to easily switch to a synth patch.
There are two different types of Program Change messages on the MPK61/MPK88:
PROG CHANGE – This event will transmit a regular Program Change message (0-127) to your DAW or an
external device, allowing you to switch between 128 different program banks.
external device, allowing you to switch between 128 different program banks.
PROG+BANK – This event transmits a Program Change message (0-127), along with a Bank L (Least
Significant Bit) Change message (0-127) and a Bank M (Most Significant Bit) Change message (0-126),
which allows access of up to 16384 different program banks. You can use PROG+BANK if your DAW or
external device supports LSB and MSB.
Significant Bit) Change message (0-127) and a Bank M (Most Significant Bit) Change message (0-126),
which allows access of up to 16384 different program banks. You can use PROG+BANK if your DAW or
external device supports LSB and MSB.
To enter Program Change mode, press the [PROGRAM CHANGE] button. Then, turn [VALUE] dial to
select either a PROG CHANGE or PROG+BANK event.
select either a PROG CHANGE or PROG+BANK event.
PROG CHANGE (Program Change)
PROG CHANGE allows you to transmit a regular Program Change
message.
message.
1.
Select PROG CHANGE with the [VALUE] dial.
2.
Press [ENTER] to see the next page of parameters.
3.
Press the [<] button to access the MIDI CH field – this is the MIDI
Channel which will be used to transmit the Program Change
message. You can change the MIDI Channel by turning the
[VALUE] dial. Then, press [>] to go to the next field.
Channel which will be used to transmit the Program Change
message. You can change the MIDI Channel by turning the
[VALUE] dial. Then, press [>] to go to the next field.
4.
In the PROG field, choose the program number with the [VALUE]
dial.
dial.
5.
Press [ENTER] to send the Program Change message.
PROG+BANK (Program Change with Bank Change)
PROG+BANK allows you to send a Program Change with Bank
Change message to your DAW or external sound module.
Change message to your DAW or external sound module.
1.
Select PROG+BANK with the [VALUE] dial.
2.
Press [ENTER] to see the next page of parameters.
3.
Press the [<] button to access the MIDI CH field – this is the MIDI
Channel which will be used to transmit the message. You can
change the MIDI Channel by turning the [VALUE] dial. Then,
press [>] to go to the next field.
Channel which will be used to transmit the message. You can
change the MIDI Channel by turning the [VALUE] dial. Then,
press [>] to go to the next field.
4.
In the PROG field, choose the program number with the [VALUE]
dial. Press [>] to go to the next field.
dial. Press [>] to go to the next field.
5.
In the BANK M field, select the MSB (Most Significant Bit) of
information. Press [>] to go to the next field.
information. Press [>] to go to the next field.
6.
In the BANK L field, select the LSB (Least Significant Bit) of
information.
information.
7.
Press [ENTER] to send the Bank and Program event.