Behringer EG2080-RW/BK Manual De Usuario
15
EUROGRAND EG2080-
RW/BK
Please note the order of voices used in the sound
combination selected, in order to understand which
settings apply to which voice in the examples
below.
combination selected, in order to understand which
settings apply to which voice in the examples
below.
A layer combination consisting of two sounds must
be set up before you can adjust the following
functions (see chapter 5.1).
be set up before you can adjust the following
functions (see chapter 5.1).
6.3.1 Volume ratio
Use this function to adjust the volume ratio of the selected sounds.
Please enter EDIT mode (see chapter 6.1) and select
the following function.
the following function.
Function:
E3.1
Value:
0
x20
Description:
10
:
Same volume for voice #1 and voice #2
<
10
:
Voice #2 louder than voice #1
>
10
:
Voice #1 louder than voice #2
6.3.2 Detune
This function allows you to detune the selected sounds slightly
against each other.
against each other.
Please enter EDIT mode (see chapter 6.1) and select
the following function.
the following function.
Function:
E3.2
Value:
-10
x10
Description:
0
:
Same pitch for voice #1 and voice #2
<
0
:
Voice #2 higher than voice #1
>
0
:
Voice #1 higher than voice #2
6.3.3 Transposition
Use this function to transpose the selected sounds up or down
by one octave. Depending on which sounds are used in a
combination, the tranpose function can help make the sounds
more homogeneous.
by one octave. Depending on which sounds are used in a
combination, the tranpose function can help make the sounds
more homogeneous.
Example:
In a combination of GRAND PIANO 1 and STRINGS the STRINGS
sound too low. In this case, it helps to transpose the STRINGS up
by one octave.
sound too low. In this case, it helps to transpose the STRINGS up
by one octave.
Please enter EDIT mode (see chapter 6.1) and select
the following function.
the following function.
Function:
E3.3
(voice #1 transposed by an octave)
E3.4
(voice #2 transposed by an octave)
Value:
-1
x1
Description:
0
:
No transposition
-1
:
Transposition down by one octave
1
:
Transposition up by one octave
6.3.4 Effect intensity
This function allows you to edit the effect intensity of the
modulation effect for the selected sounds.
modulation effect for the selected sounds.
Please enter EDIT mode (see chapter 6.1) and select
the following function.
the following function.
Function:
E3.5
(effect intensity voice #1)
E3.6
(effect intensity voice #2)
Value:
0
x20
Description:
1
x20
: Effect intensity (default setting)
0
:
No effect
6.3.5 Reset
Use this function to reset all settings in layer mode.
Please enter EDIT mode (see chapter 6.1) and select
the following function.
the following function.
Function:
E3.7
Value:
-
Description:
Press the +/YES button to execute this function.
6.4 Using the metronome
The EG2080 features a built-in metronome which can be used
for practising or to make recordings with the internal music
sequencer.
for practising or to make recordings with the internal music
sequencer.
To use the metronome, please proceed as follows :
1) Press the METRONOME button to start or stop the
metronome.
The metronome beats are shown by flashing dots on the display.
At the beginning of a measure all dots light up simultaneously.
At the beginning of a measure all dots light up simultaneously.
2) Keep pressing the SELECT button in the TEMPO/EDIT MODE
section until the TEMPO LED lights up.
3) Use the two
ef
buttons to adjust a tempo of your choice.
4) Press and hold the METRONOME button while adjusting the
number of beats per measure using the -/NO and +/YES
button in the VALUE/SONG section.
button in the VALUE/SONG section.
+
6. ADVANCED OPERATION