Yamaha 01V96i Manual De Usuario
104
MIDI
01V96i—Reference Manual
Assigning Parameters to
Control Changes for
Real-time Control
Control Changes for
Real-time Control
You can assign 01V96i parameters to MIDI Control Changes
for real-time control. When the 01V96i receives a Control
Change, the assigned 01V96i parameter is set accordingly.
Also, when you adjust a parameter on the 01V96i, the 01V96i
transmits the assigned Control Change message.
for real-time control. When the 01V96i receives a Control
Change, the assigned 01V96i parameter is set accordingly.
Also, when you adjust a parameter on the 01V96i, the 01V96i
transmits the assigned Control Change message.
1.
Press the DISPLAY ACCESS [DIO/SETUP] but-
ton repeatedly until the DIO/Setup |
MIDI/Host page appears, then specify ports
for transmission and reception of MIDI mes-
sages (see page 101).
ton repeatedly until the DIO/Setup |
MIDI/Host page appears, then specify ports
for transmission and reception of MIDI mes-
sages (see page 101).
2.
Make connections using the ports selected in
Step 1 so that the 01V96i can transfer MIDI
messages to and from the external device.
Step 1 so that the 01V96i can transfer MIDI
messages to and from the external device.
3.
Press the DISPLAY ACCESS [MIDI] button,
then press the [F3] button.
then press the [F3] button.
The MIDI | Ctl Asgn page appears. This page enables you
to assign 01V96i parameters to Control Changes.
to assign 01V96i parameters to Control Changes.
4.
Move the cursor to the MODE parameter’s
TABLE button (
TABLE button (
1
), then press [ENTER].
The MODE parameter determines which MIDI messages
are transmitted when 01V96i parameters are adjusted.
The following options are available for the MODE
parameter:
are transmitted when 01V96i parameters are adjusted.
The following options are available for the MODE
parameter:
• TABLE
MIDI Control Change messages are transmitted in accor-
dance with the assignments on this page.
dance with the assignments on this page.
• NRPN
The assignments on the Ctl Asgn page are ignored, and
predefined NRPNs (Non Registered Parameter Num-
bers) are transmitted for remote control.
predefined NRPNs (Non Registered Parameter Num-
bers) are transmitted for remote control.
5.
If you turned on the TABLE button in Step 4,
move the cursor to a parameter box in the No.
(CH) column, then rotate the Parameter
wheel or press the [INC]/[DEC] buttons to
select the MIDI channels and Control
Changes to which you want to assign param-
eters.
move the cursor to a parameter box in the No.
(CH) column, then rotate the Parameter
wheel or press the [INC]/[DEC] buttons to
select the MIDI channels and Control
Changes to which you want to assign param-
eters.
You can assign parameters to up to 16-channel Control
Changes on the Ctl Asgn page, regardless of the MIDI
Channels currently selected for transmission and recep-
tion.
Skip Steps 5 and 6 if you turned on the NRPN button in
Step 4.
Changes on the Ctl Asgn page, regardless of the MIDI
Channels currently selected for transmission and recep-
tion.
Skip Steps 5 and 6 if you turned on the NRPN button in
Step 4.
6.
Select parameters in the parameter boxes in
the three PARAMETER columns.
the three PARAMETER columns.
Select a parameter group in the parameter box in the first
PARAMETER column, and specify the desired values in
the parameter boxes in the second and third PARAME-
TER columns.
The following parameters and values are available:
PARAMETER column, and specify the desired values in
the parameter boxes in the second and third PARAME-
TER columns.
The following parameters and values are available:
Tip:
You can store a Parameter to Control Change assignment
table to an external device by using MIDI Bulk Dump or the Stu-
dio Manager software.
dio Manager software.
Tip:
See page 157 for information on the default Parameter
to Control Change assignments.
1
Tip:
NRPNs are special MIDI messages that combine three
different Control Changes. They enable you to control many
parameters on a single MIDI Channel.
parameters on a single MIDI Channel.
HIGH
MID
LOW
NO ASSIGN
—
—
FADER H
CHANNEL
INPUT1–32/ST IN1–4
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
INPUT1–32/ST IN1–4
AUX2 SEND
AUX3 SEND
AUX4 SEND
AUX5 SEND
AUX6 SEND
AUX7 SEND
AUX8 SEND
BUS TO ST
BUS1–8
FADER L
CHANNEL
INPUT1–32/ST IN1–4
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
INPUT1–32/ST IN1–4
AUX2 SEND
AUX3 SEND
AUX4 SEND
AUX5 SEND
AUX6 SEND
AUX7 SEND
AUX8 SEND
BUS TO ST
BUS1–8