Yamaha 01V96i Manual De Usuario
Monitoring
49
01V96i—Reference Manual
Monito
ri
ng
Monitoring
This chapter explains how to set up monitoring and use the
Solo function on the 01V96i.
Solo function on the 01V96i.
Monitor
The 01V96i features the stereo signal path to feed the moni-
tors. The monitoring signal source is patched to MONITOR
OUT connectors L & R and the PHONES connector.
The following diagram illustrates the monitoring signal flow.
tors. The monitoring signal source is patched to MONITOR
OUT connectors L & R and the PHONES connector.
The following diagram illustrates the monitoring signal flow.
• SOLO bus
This special bus routes soloed Input Channels to the
Monitor outputs, bypassing Bus 1–8 and the Stereo Bus.
Monitor outputs, bypassing Bus 1–8 and the Stereo Bus.
• OUTPUT SOLO
This section routes soloed Output Channels (Aux Out
1–8, Bus Out 1–8) to the Monitor outputs.
1–8, Bus Out 1–8) to the Monitor outputs.
• MONITOR TRIM
This section adjusts the monitoring signal level in the dig-
ital domain.
ital domain.
• MONITOR OUT LEVEL
Use the MONITOR [MONITOR OUT] control on the
top panel to adjust the monitoring signal level in the ana-
log domain.
top panel to adjust the monitoring signal level in the ana-
log domain.
• MONITOR/2TR IN
As a monitoring signal, you can select either the 01V96i
internal signals or 2TR IN digital inputs.
internal signals or 2TR IN digital inputs.
• PHONES
The Monitor signal is also fed to the PHONES jack. You
can set the level independently.
can set the level independently.
Monitor and Solo Setup
For monitoring and solo setup, press the DISPLAY ACCESS
[DIO/SETUP] button repeatedly until the DIO/Setup | Mon-
itor page appears.
[DIO/SETUP] button repeatedly until the DIO/Setup | Mon-
itor page appears.
This page contains the following parameters:
1
SOLO
This parameter turns the Solo function on or off. By
default, it is set to Enabled.
This parameter turns the Solo function on or off. By
default, it is set to Enabled.
2
MODE
This parameter determines how the Solo function works.
There are two options. The setting affects only Input
Channels.
This parameter determines how the Solo function works.
There are two options. The setting affects only Input
Channels.
• RECORDING
In Recording Solo mode, soloed Input Channel signals
are fed to the Solo bus and output via the Monitor out-
puts. Other buses (Stereo bus and Bus 1–8) are unaffected
by this mode.
are fed to the Solo bus and output via the Monitor out-
puts. Other buses (Stereo bus and Bus 1–8) are unaffected
by this mode.
• MIXDOWN
In Mixdown Solo mode, soloed Input Channel signals are
fed to the Stereo bus and output via the Monitor outputs.
Unsoloed Input Channels are not fed to the Stereo bus
while the Solo function is enabled.
fed to the Stereo bus and output via the Monitor outputs.
Unsoloed Input Channels are not fed to the Stereo bus
while the Solo function is enabled.
Note:
Input and Output Channels cannot be solo-monitored
simultaneously. The solo function for the most-recently
soloed channels is enabled.
soloed channels is enabled.
SOLO LOGIC
MONO
BUS1-8
AUX1-8
AUX1-8
8
8
8
OUTPUT SOLO
SOLO TRIM
SOLO R
SOLO L
SOLO L
SOLO R
STEREO L
STEREO R
MONITOR TRIM
[PHONES]
PHONES
LEVEL
LEVEL
[MONITOR OUT]
L
R
MONITOR OUT
LEVEL
DA
DA
[2TR IN]
RCA
L
R
MONITOR
/2TR IN
/2TR IN
Tip:
•
•
Recording Solo mode is convenient when you wish to mon-
itor certain Input Channels while recording, since the Ste-
reo bus and Bus 1–8 signals are unaffected.
itor certain Input Channels while recording, since the Ste-
reo bus and Bus 1–8 signals are unaffected.
•
Mixdown Solo mode is useful when you wish to mute
unsoloed Input Channels and feed soloed Input Channel
signals to the Stereo bus during mixdown.
unsoloed Input Channels and feed soloed Input Channel
signals to the Stereo bus during mixdown.
8
9
7
3
4
2
1
6
5