Yamaha 01V96i Manual De Usuario
Nuendo/Cubase Remote Layer
93
01V96i—Reference Manual
Remote Co
ntro
l
Automation
If you assign a parameter that controls Pro Tools Automation
mode (such as DAW Auto Read, DAW Auto Touch, etc.) to
one of the User Defined buttons, you can control the Automa-
tion settings for each channel by using that User Defined but-
ton. For more information on assigning functions to the user
defined keys, refer to “Using the User Defined Keys” in the
Owner’s Manual (separate booklet).
Press the STEREO OUT channel [SEL] button. The button
indicator lights up, and the Channel 1–16 [SEL] buttons
become available for the Automation mode setting.
Press the desired channel [SEL] buttons while pressing the
programmed User Defined button to switch the correspond-
ing channels’ Automation settings.
While the channel [SEL] buttons are available for the Auto-
mation mode setting, pressing the [SEL] buttons will cause
the Fader Touch or Untouch command to be transmitted to
Pro Tools. This is useful for Automation punch in and out
recording.
mode (such as DAW Auto Read, DAW Auto Touch, etc.) to
one of the User Defined buttons, you can control the Automa-
tion settings for each channel by using that User Defined but-
ton. For more information on assigning functions to the user
defined keys, refer to “Using the User Defined Keys” in the
Owner’s Manual (separate booklet).
Press the STEREO OUT channel [SEL] button. The button
indicator lights up, and the Channel 1–16 [SEL] buttons
become available for the Automation mode setting.
Press the desired channel [SEL] buttons while pressing the
programmed User Defined button to switch the correspond-
ing channels’ Automation settings.
While the channel [SEL] buttons are available for the Auto-
mation mode setting, pressing the [SEL] buttons will cause
the Fader Touch or Untouch command to be transmitted to
Pro Tools. This is useful for Automation punch in and out
recording.
Depending on the currently-selected Automation mode, the
channel [SEL] button indicators operate as follows:
channel [SEL] button indicators operate as follows:
Nuendo/Cubase Remote
Layer
Layer
You can remotely control Nuendo and Cubase using the
Remote Layer.
Remote Layer.
■ Configuring Computers
1.
Download the Yamaha Steinberg USB Driver
from the following URL, and install the driver
as described in the included installation
guide.
http://www.yamahaproaudio.com/
from the following URL, and install the driver
as described in the included installation
guide.
http://www.yamahaproaudio.com/
2.
Use a USB cable to connect the 01V96i.
3.
Make sure that the 01V96i is powered-on.
4.
Launch Nuendo/Cubase, select the Device
Setup menu, and set up Nuendo/Cubase so
that the 01V96i can communicate with the
software.
Setup menu, and set up Nuendo/Cubase so
that the 01V96i can communicate with the
software.
Refer to the Nuendo/Cubase User’s Manual for more
information on setting up the software.
information on setting up the software.
■ Configuring the 01V96i
1.
Refer to page 84 to configure the DIO/Setup
| MIDI/HOST page.
| MIDI/HOST page.
2.
Press the LAYER [REMOTE] button to set the
TARGET parameter to Nuendo/Cubase.
TARGET parameter to Nuendo/Cubase.
You can now remotely control Nuendo/Cubase using the
Remote Layer.
Remote Layer.
Note:
Operating a fader also causes the Fader Touch command
to be transmitted. Also, whenever the transport mode changes
(such as Play and Stop), the Fader Untouch command is trans-
mitted.
(such as Play and Stop), the Fader Untouch command is trans-
mitted.
User Defined Keys
Function
Pro Tools
Automation
Mode
[SEL] Button
Indicators
DAW AUTO WRITE
Auto write
Flashing red
(Record Ready)
Red (Recording)
(Record Ready)
Red (Recording)
DAW AUTO TOUTCH
Auto touch
DAW AUTO LATCH
Auto latch
DAW AUTO READ
Auto read
Illuminated
steadily
steadily
DAW AUTO OFF
Auto off
Off