Behringer DJX700 Manual De Usuario

PRO MIXER DJX700

4. SPECIFICATIONS

AUDIO INPUTS

Mic

40 dB Gain, XLR,

electronically balanced input stage

Phono in

40 dB Gain, unbalanced input

Line in

0 dB Gain, unbalanced inputs

CD in

0 dB Gain, unbalanced inputs

Return

0 dB Gain, unbalanced input

AUDIO OUTPUTS

Master

max. +21 dBu

Booth

max. +21 dBu

Tape

typ. 0 dBu

Send

typ. 0 dBu

Phones Out

max. 180 mW @ 75 Ω / 1% THD

EQUALIZER

Stereo Low

+12 dB/-32 dB @ 50 Hz

Stereo Mid

+12 dB/-32 dB @ 1.2 kHz

Stereo High

+12 dB/-32 dB @ 10 kHz

Mic Low

+15 dB/-15 dB @ 80 Hz

Mic Mid

+15 dB/-15 dB @ 2.5 kHz

Mic High

+15 dB/-15 dB @ 12 kHz

Kill Low

-54 dB @ 50 Hz

Kill Mid

-44 dB @ 1 kHz

Kill High

-26 dB @ 10 kHz

DIGITAL EFFECTS PROCESSOR

DSP

24-bit TEXAS INSTRUMENTS

A/D-D/A converter

24-bit Sigma-Delta,

64/128-times oversampling

Sampling rate

46.875 kHz

SYSTEM SPECIFICATIONS

Signal-to-noise ratio

> 80 dB (Line)

Crosstalk

> 70 dB (Line)

Distortion (THD)

< 0.03%

Frequency response 10 Hz - 55 kHz, +0/-3 dB

POWER SUPPLY

Mains voltages

USA/Canada

120 V~, 60 Hz

Europe/U.K./Australia

230 V~, 50 Hz

Japan

100 V~, 50 - 60 Hz

General export model

120/230 V~, 50 - 60 Hz

Power consumption

32 W

Fuse

100 - 120 V~: T 1 A H

200 - 240 V~: T 500 mA H

Mains connection

Standard IEC receptacle

DIMENSIONS/WEIGHT

Dimensions (H x W x D) approx. 4 1/10" (104.3 mm)

x 12 1/20" (320 mm)

x 14 3/5" (370.8 mm)

Weight

approx. 3.9 kg (8 1/2 lbs)

BEHRINGER makes every effort to ensure the highest standard of quality. Necessary

modifications are carried out without notice. Thus, the specifications and design of the device

may differ from the information given in this manual.

The externally processed signal is added to the MASTER

output signal via the RETURN connectors. The effect

signal volume may only be adjusted at the output control

of the effects device itself.
The MASTER output is for connecting to an amplifier and

can be adjusted with the MASTER fader

Always turn the power amps on last to avoid inrush

currents that can easily damage your speakers.

And, to avoid sudden and unpleasant surprises

for your ears, make sure there is no signal at the

DJX700 before turning on the power amps. To be

sure, slide all the faders to the bottom and switch

all controls to the zero position.
The BOOTH output gives you an additional option of

connecting an amplifier in order to, for example, feed the

signal into your monitors or to bring sound to an extra area.

The BOOTH output level is regulated by using the BOOTH

LEVEL control

of the MASTER section.

Using the TAPE output you can record your music by

connecting devices such as tape decks, DAT recorders

etc. Unlike the MASTER output, the output volume is fixed,

making it necessary for you to adjust the input level on the

recording device.
The POWER switch powers the DJX700 on. You should

always make sure that the POWER switch is in the Off

position when initially connecting the unit to the mains.

Please take note: Merely switching the unit off does

not mean that it is fully disconnected from the

mains. When not using the unit for prolonged

periods of time, please unplug the units power

cord from the power outlet.

This is the connector for the power cable. This is where

the advantage of a sophisticated internal power supply

can be seen: the pulse behaviour of each amplifying circuit

is mainly determined by the voltage reserves available.

Each mixing console is equipped with numerous

operational amplifiers (op amps) to process line level

signals. Due to limited output of their power supplies,

many mixing consoles show signs of stress when

subjected to heavy loads. But not your DJX700: the sound

is always clear and transparent.
FUSE HOLDER / VOLTAGE SETTING. Before connecting

the unit to the mains, ensure that the voltage setting

matches your local voltage. Blown fuses should only be

replaced by a fuse of the same type and rating. On some

units, the fuses holder can be switched to one of two

positions, i.e. 230 V and 120 V. Please note: should you

desire to operate the unit outside Europe at 120 V, a

higher fuse rating is required.

To disconnect power from main, pull out the main

cord plug. When installing the product, ensure that

the plug is easily accessible. If mounting in a rack,

ensure that the mains can be easily disconnected

by a plug or by an all-pole disconnect switch on or

near the rack.

SERIAL NUMBER. Please take the time to complete and

return the warranty card within 14 days of the date of

purchase. Or, simply register online at

www.behringer.com.

4. SPECIFICATIONS