Harbor Freight Tools 38160 Manual De Usuario
Page 3
For technical questions, please call 1-800-444-3353.
SKU 38160
USE RIGHT TOOL. Don’t force tool or
8.
attachment to do a job for which it was
not designed.
not designed.
recOMMended MiniMuM Wire
gauge FOr eXtensiOn cOrds
(120 VOlt)
naMeplate
aMperes
(at full load)
eXtensiOn cOrd
length
25’
50’
100’
150’
0 – 6
18
16
16
14
6.1 – 10
18
16
14
12
10.1 – 12
16
16
14
12
12.1 – 16
14
12
do not use.
table a
USE PROPER EXTENSION CORD.
9.
Make sure your extension cord is in good
condition. When using an extension
cord, be sure to use one heavy enough
to carry the current your product will
draw. An undersized cord will cause a
drop in line voltage resulting in loss of
power and overheating.
condition. When using an extension
cord, be sure to use one heavy enough
to carry the current your product will
draw. An undersized cord will cause a
drop in line voltage resulting in loss of
power and overheating.
Table A shows
the correct size to use depending on
cord length and nameplate ampere
rating. If in doubt, use the next heavier
gauge. The smaller the gauge number,
the heavier the cord.
cord length and nameplate ampere
rating. If in doubt, use the next heavier
gauge. The smaller the gauge number,
the heavier the cord.
WEAR PROPER APPAREL. Do not wear
10.
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Nonslip footwear
is recommended. Wear protective hair
covering to contain long hair.
bracelets, or other jewelry which may get
caught in moving parts. Nonslip footwear
is recommended. Wear protective hair
covering to contain long hair.
ALWAYS USE SAFETY GLASSES. Also
11.
use face or dust mask if cutting operation
is dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT
safety glasses.
is dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT
safety glasses.
SECURE WORK. Use clamps or a vise
12.
to hold work when practical. It’s safer
than using your hand and it frees both
hands to operate tool.
than using your hand and it frees both
hands to operate tool.
DON’T OVERREACH. Keep proper
13.
footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep
14.
tools sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
performance. Follow instructions for
lubricating and changing accessories.
DISCONNECT TOOLS before servicing;
15.
when changing accessories, such as
blades, bits, cutters, and the like.
blades, bits, cutters, and the like.
REDUCE THE RISK OF
16.
UNINTENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
sure switch is in off position before
plugging in.
USE RECOMMENDED ACCESSORIES.
17.
Consult the owner’s manual for
recommended accessories. The use of
improper accessories may cause risk of
injury to persons.
recommended accessories. The use of
improper accessories may cause risk of
injury to persons.
NEVER STAND ON TOOL. Serious
18.
injury could occur if the tool is tipped
or if the cutting tool is unintentionally
contacted.
or if the cutting tool is unintentionally
contacted.
CHECK DAMAGED PARTS. Before
19.
further use of the tool, a guard or other
part that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended
function – check for alignment of moving
parts, binding of moving parts, breakage
of parts, mounting, and any other
conditions that may affect its operation.
A guard or other part that is damaged
should be properly repaired or replaced.
part that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended
function – check for alignment of moving
parts, binding of moving parts, breakage
of parts, mounting, and any other
conditions that may affect its operation.
A guard or other part that is damaged
should be properly repaired or replaced.
DIRECTION OF FEED. Feed work into
20.
a blade or cutter against the direction of
rotation of the blade or cutter only.
rotation of the blade or cutter only.
NEVER LEAVE TOOL RUNNING
21.
UNATTENDED. TURN POWER OFF.
Don’t leave tool until it comes to a
complete stop.
Don’t leave tool until it comes to a
complete stop.
reV 10e