Cypress CY7C1241V18 Manual De Usuario
CY7C1241V18, CY7C1256V18
CY7C1243V18, CY7C1245V18
CY7C1243V18, CY7C1245V18
Document Number: 001-06365 Rev. *D
Page 9 of 28
Depth Expansion
The CY7C1243V18 has a Port Select input for each port. This
enables easy depth expansion. Both Port Selects are sampled
on the rising edge of the Positive Input Clock only (K). Each port
select input can deselect the specified port. Deselecting a port
does not affect the other port. All pending transactions (read and
write) are completed before the device is deselected.
enables easy depth expansion. Both Port Selects are sampled
on the rising edge of the Positive Input Clock only (K). Each port
select input can deselect the specified port. Deselecting a port
does not affect the other port. All pending transactions (read and
write) are completed before the device is deselected.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and V
on the SRAM and V
SS
to enable the SRAM to adjust its output
driver impedance. The value of RQ must be 5X the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15% is between 175
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15% is between 175
Ω and 350Ω
,
with V
DDQ
= 1.5V. The
output impedance is adjusted every 1024 cycles upon power up
to account for drifts in supply voltage and temperature.
to account for drifts in supply voltage and temperature.
Echo Clocks
Echo clocks are provided on the QDR-II+ to simplify data capture
on high speed systems. Two echo clocks are generated by the
QDR-II+. CQ is referenced with respect to K and CQ is refer-
enced with respect to K. These are free running clocks and are
synchronized to the input
on high speed systems. Two echo clocks are generated by the
QDR-II+. CQ is referenced with respect to K and CQ is refer-
enced with respect to K. These are free running clocks and are
synchronized to the input
clock of the QDR-II+. The timing for the
echo clocks is shown in
Valid Data Indicator (QVLD)
QVLD is provided on the QDR-II+ to simplify data capture on high
speed systems. The QVLD is generated by the QDR-II+ device
along with data output. This signal is also edge-aligned with the
echo clock and follows the timing of any data pin. This signal is
asserted half a cycle before valid data arrives.
speed systems. The QVLD is generated by the QDR-II+ device
along with data output. This signal is also edge-aligned with the
echo clock and follows the timing of any data pin. This signal is
asserted half a cycle before valid data arrives.
Delay Lock Loop (DLL)
These chips use a DLL that is designed to function between 120
MHz and the specified maximum clock frequency. The DLL may
be disabled by applying ground to the DOFF pin. When the DLL
is turned off, the device behaves in QDR-I mode (with 1.0 cycle
latency and a longer access time). For more information, refer to
the application note, DLL Considerations in
QDRII/DDRII/QDRII+/DDRII+. The DLL can also be reset by
slowing or stopping the input clocks K and K for a minimum of 30
ns. However, it is not necessary for the DLL to be reset to lock to
the desired frequency. During power up, when the DOFF is tied
HIGH, the DLL is locked after 2048 cycles of stable clock.
MHz and the specified maximum clock frequency. The DLL may
be disabled by applying ground to the DOFF pin. When the DLL
is turned off, the device behaves in QDR-I mode (with 1.0 cycle
latency and a longer access time). For more information, refer to
the application note, DLL Considerations in
QDRII/DDRII/QDRII+/DDRII+. The DLL can also be reset by
slowing or stopping the input clocks K and K for a minimum of 30
ns. However, it is not necessary for the DLL to be reset to lock to
the desired frequency. During power up, when the DOFF is tied
HIGH, the DLL is locked after 2048 cycles of stable clock.