SMC Networks LH79520 SoC ARM720T Manual De Usuario
ARM720T_LH79520 – Sharp LH79520 SoC with ARM720T 32-bit RISC Processor
• cs0 (Bank 0) – 4000_0000h to 43FF_FFFFh
• cs1 (Bank 1) – 4400_0000h to 47FF_FFFFh
• cs1 (Bank 1) – 4400_0000h to 47FF_FFFFh
The bank select signals
arrive at the processor's
wrapper component in
the FPGA on the
PER_CS bus.
arrive at the processor's
wrapper component in
the FPGA on the
PER_CS bus.
• cs2 (Bank 2) – 4800_0000h to 4BFF_FFFFh
• cs3 (Bank 3) – 4C00_0000h to 4FFF_FFFFh
• cs4 (Bank 4) – 5000_0000h to 53FF_FFFFh
• cs5 (Bank 5) – 5400_0000h to 57FF_FFFFh
• cs6 (Bank 6) – 5800_0000h to 5BFF_FFFFh
• cs3 (Bank 3) – 4C00_0000h to 4FFF_FFFFh
• cs4 (Bank 4) – 5000_0000h to 53FF_FFFFh
• cs5 (Bank 5) – 5400_0000h to 57FF_FFFFh
• cs6 (Bank 6) – 5800_0000h to 5BFF_FFFFh
The block of addresses between 5C00_0000h and 5FFF_FFFFh are RESERVED. Software should not access this range of
addresses as doing so will not generate a data abort.
addresses as doing so will not generate a data abort.
In addition, the lowest bank of external memory – Bank 0 – is mirrored to the lowest page (512MBytes) of the processor's
address space, in the range 0000_0000h to 1FFF_FFFFh. This occurs by default after a reset is issued and ensures that
exception vectors are correctly placed at addresses 0000_0000h to 0000_001Ch.
address space, in the range 0000_0000h to 1FFF_FFFFh. This occurs by default after a reset is issued and ensures that
exception vectors are correctly placed at addresses 0000_0000h to 0000_001Ch.
Of the seven banks of external memory available, six (cs0-cs5) are used by the ARM720T_LH79520 wrapper when mapping
external devices defined in the FPGA.
external devices defined in the FPGA.
When configuring the processor's memory from within the FPGA design, the External Static Memory is simplified by dividing it
into three regions:
• Peripheral I/O – Bank 5
• External Memory – Banks 1-4
• Internal Memory – Bank 0.
into three regions:
• Peripheral I/O – Bank 5
• External Memory – Banks 1-4
• Internal Memory – Bank 0.
Figure 7 summarizes how these three regions correspond (or are mapped into) the External Static Memory regions of the
processor's full address space.
processor's full address space.
Figure 7. How FPGA-based memory and peripherals map into the physical LH79520's address space.
Internal Memory
The internal "Low" or "Boot" RAM is built using true dual-port FPGA block RAM memory. As such, it can be read or written on
both sides, simultaneously, in a single cycle.
both sides, simultaneously, in a single cycle.
This memory still has the standard limitation of load delay slots, because the load from memory happens further down the
pipeline, after the Execute stage. As a result, any operation that requires loaded data in the cycle immediately after the load will
cause the processor to insert a load stall, holding the first half of the pipeline for one cycle while the data becomes available.
pipeline, after the Execute stage. As a result, any operation that requires loaded data in the cycle immediately after the load will
cause the processor to insert a load stall, holding the first half of the pipeline for one cycle while the data becomes available.
Other than this single limitation, the RAM block is as fast as the internal processor registers themselves.
CR0162 (v2.0) March 10, 2008
13