Manualsbrain.com
  1. Manuales
  2. Marcas
  3. Cisco
  4. 1-Port ISDN BRI WAN Interface Card
  5. Hoja De Datos

Cisco 1-Port ISDN BRI WAN Interface Card WIC-1B-S/T= Hoja De Datos

Los códigos de productos
WIC-1B-S/T=
Descargar
Página de 4
Cisco Systems, Inc.
All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement.
Page 3 of 4
Features
Table 2 gives the features of the ISDN BRI S/T WICs.
Platform Support
Table 3 gives an overview of Cisco IOS support on a by platform basis.
Table 2
Features of ISDN BRI S/T WICs
WIC36-1B-S/T
WIC-1B-S/T
WIC-1B-S/T-V2
• One ISDN BRI port (S/T interface, requires
external NT1)
• RJ-45 connector
• Not compatible with Cisco 1600, 1720,
2600, or 3700 series
• Does not support hot swapping; however,
no hardware damage will occur if it is
swapped while power is on
• Maximum of one per NM-1E2W,
NM-1E1R2W, and NM-2E2W card
• Insert only into slot W1 of the 1E2W, 2E2W,
and 1E1R2W network modules (the
network module is physically keyed)
• Not supported in NM-1FE1R2W,
NM-1FE2W, NM-2FE2W, or NM-2W
• Cannot mix in same network module with
a WIC-1B-S/T WIC
• (a WIC-1B-S/T can be used in a different
network module in the same chassis)
• End-of-sale date August 31,1997
• One ISDN BRI port (S/T interface, requires
external NT1)
• RJ-45 connector
• Supported on Cisco 1600, 1700, 2600,
3600, and 3700 series
• Cannot be used with Cisco 1603 or 1604
base units
• Does not support hot swapping; however,
no hardware damage will occur if it is
swapped while power is onb
• Can go into slot W0 or W1 of the 1E2W,
2E2W, and 1E1R2W network modules
• Supported in NM-1FE1R2W, NM-1FE2W,
NM-2FE2W, and NM-2W
• Cannot insert into same network module
that already has a WIC36-1B-S/T card
(a WIC36-1B-S/T can be used in a different
network module in the same chassis)
• One ISDN BRI port (S/T interface, requires
external NT1)
• RJ-45 connector
• Supported on Cisco 1700, 2600, 3600, and
3700 series
• Cannot be used with Cisco 1600 Series or
the Cisco 1750
• Does not support hot swapping; however,
no hardware damage will occur if it is
swapped while power is on
• Can go into slot W0 or W1 of the 1E2W,
2E2W, and 1E1R2W network modules
• Supported in NM-1FE1R2W, NM-1FE2W,
NM-2FE2W, and NM-2W
• Cannot insert into the same network
module that already has a WIC36-1B-S/T
card
(a WIC36-1B-S/T can be used in a different
network module in the same chassis)
Table 3
Cisco IOS Support
Platfor
m
Cisco
1601(R)
, 1602
(R), and
1605-R
Cisco
1603,
1603-R,
1604,
and
1604-R
Cisco
1720,
1721,
1751,
1760
Cisco
1750
Cisco 2600 and
2600XM
Cisco 3620 and
3640
Cisco
3631
Cisco 3660
Cisco 2691, 3725,
and 3745
Carrier
module
Not
required
Not
required
Not
required
Not
required
Onboard
NM-2W
NM-1E2
W,
NM-1E1
R2W,
and
NM-2E2
W
NM-1FE
2W,
NM-1FE
1R2W,
NM-2FE
2W, and
NM-2W
Not
required
NM-1E2
W,
NM-1E1
R2W,
and
NM-2E2
W
NM-1FE
2W,
NM-1FE
1R2W,
and
NM-2FE
2W,
NM-2W
Onboard
NM-1FE
2W,
NM-1FE
1R2W,
NM-2FE
2W, and
NM-2W
WIC-1B-
S/T
All
Cisco
IOS
releases
Not
support
ed
All
Cisco
IOS
releases
All
Cisco
IOS
releases
All Cisco IOS
releases
All Cisco IOS
releases 11.2(4)XA,
11.2(5)P, all 11.3,
11.3T, and all 12.x
All
Cisco
IOS
releases
All Cisco IOS
releases
All Cisco IOS
releases
WIC36-1
B-S/T
Not
support
ed
Not
support
ed
Not
support
ed
Not
support
ed
Not supported
Releases 11.x, 12.0,
12.0T, 12.1, 12.1T,
and 12.2;not
supported in 12.2T
Not
support
ed
Not supported
Not supported
WIC-1B-
S/T-V2
Not
support
ed
Not
support
ed
First
support
ed in
12.0(25),
12.1(19),
12.2(16),
and
12.3(1)
Not
support
ed
First supported in
12.0(25), 12.1(19),
12.2(16), and 12.3(1)
First supported in
12.0(25), 12.1(19),
12.2(16), and 12.3(1)
First
support
ed
12.3(1)
First supported in
12.0(25), 12.1(19),
12.2(16), and 12.3(1)
First supported in
12.3(1)