ATTO Technology 2500C Manual De Usuario
57
ATTO Technology Inc. iPBridge Installation and Operation Manual
7.1.10 Mapping commands
You may map devices via the web-based server or through the management or serial ports. Refer to
on page 13 and
on page 15 for details.
AutoMap
Automatically assigns a subset of NDMP device name
protocol addresses or iSCSI LUNs to a subset of SCSI
target destination devices visible to the iPBridge. Valid
existing maps are not deleted.
Automatically assigns a subset of NDMP device name
protocol addresses or iSCSI LUNs to a subset of SCSI
target destination devices visible to the iPBridge. Valid
existing maps are not deleted.
Immediate command: AutoMap
iSCSITarget
Creates/deletes an iSCSI target name. The target name
acts as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing. Multiple Target mode must be enabled
to use this command. In verbose mode, overwriting a map
requires secondary confirmation of the action.
Creates/deletes an iSCSI target name. The target name
acts as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing. Multiple Target mode must be enabled
to use this command. In verbose mode, overwriting a map
requires secondary confirmation of the action.
Immediate command: iSCSI [Target Name] <delete>
iSCSITargetNameDisplay
Displays the iSCSI target name. If Multiple Target mode
is enabled, iSCSI target names are listed for all existing
iSCSI targets.
Displays the iSCSI target name. If Multiple Target mode
is enabled, iSCSI target names are listed for all existing
iSCSI targets.
Immediate command: iSCSITargetNameDisplay
MultiTargetMode
Enables/disables iSCSI multiple target mode addressing
on the iPBridge. If enabled, all previous maps are
deleted. In verbose mode, overwriting a map requires
secondary confirmation of the action.
Enables/disables iSCSI multiple target mode addressing
on the iPBridge. If enabled, all previous maps are
deleted. In verbose mode, overwriting a map requires
secondary confirmation of the action.
Default: disabled
Set syntax: set MultiTargetMode [enabled | disabled]
Get syntax: get MultiTargetMode
Set syntax: set MultiTargetMode [enabled | disabled]
Get syntax: get MultiTargetMode
Route
Assigns a host protocol address to a target destination
device.
For NDMP, assigns an NDMP device name to a target
destination device. More than one NDMP name may be
assigned to a SCSI BTL. If you try to map a new SCSI BTL
Assigns a host protocol address to a target destination
device.
For NDMP, assigns an NDMP device name to a target
destination device. More than one NDMP name may be
assigned to a SCSI BTL. If you try to map a new SCSI BTL
to the same NDMP name, the new BTL overwrites the
previous map. Using the Delete identifier removes the
map from the map table. In verbose mode, overwriting a
map requires secondary confirmation of the action.
previous map. Using the Delete identifier removes the
map from the map table. In verbose mode, overwriting a
map requires secondary confirmation of the action.
Immediate command: Route NDMP [Tape | SCSI]
[srcName] [SCSI [bb tt ll] | Delete]
[srcName] [SCSI [bb tt ll] | Delete]
For iSCSI, assigns an iSCSI protocol address to a target
destination device. If Multiple Target mode has been
enabled, a valid target name must be specified. If you try
to map a new SCSI BTL to the same iSCSI LUN, the new
BTL overwrites the previous map. Using the Delete
identifier removes the map from its map table. In verbose
mode, overwriting a map requires secondary
confirmation of the action.
destination device. If Multiple Target mode has been
enabled, a valid target name must be specified. If you try
to map a new SCSI BTL to the same iSCSI LUN, the new
BTL overwrites the previous map. Using the Delete
identifier removes the map from its map table. In verbose
mode, overwriting a map requires secondary
confirmation of the action.
Immediate command in single target mode:
Route iSCSI [lun] [SCSI [bb tt ll] | Delete]
Immediate command in multiple target mode:
Route iSCSI [Target Name] [lun] [SCSI [bb tt ll] | Delete]
Route iSCSI [lun] [SCSI [bb tt ll] | Delete]
Immediate command in multiple target mode:
Route iSCSI [Target Name] [lun] [SCSI [bb tt ll] | Delete]
RouteDisplay
Displays a list of host protocol-to-SCSI address
mappings on the bridge.
For NDMP, displays a list of NDMP name to SCSI Bus,
Target, LUN mappings. The optional name parameter
limits the list to the maps which satisfy a search for the
given name.
Displays a list of host protocol-to-SCSI address
mappings on the bridge.
For NDMP, displays a list of NDMP name to SCSI Bus,
Target, LUN mappings. The optional name parameter
limits the list to the maps which satisfy a search for the
given name.
NumEntries: decimal number of map lines displayed
Name: 32-character NDMP device name
type: NDMP
map type: either Tape or SCSI
sb: decimal SCSI bus number
st: decimal SCSI target number
sl: decimal SCSI LUN number
Name: 32-character NDMP device name
type: NDMP
map type: either Tape or SCSI
sb: decimal SCSI bus number
st: decimal SCSI target number
sl: decimal SCSI LUN number
Immediate command: RouteDisplay NDMP <Name>
For iSCSI, displays a list of iSCSI to SCSI Bus, Target,
LUN mappings. If Multiple Target mode has been
enabled, the optional Target Name parameter limits the
list to the maps which satisfy a search for the given target
name. In either mode, the optional LUN parameter limit
LUN mappings. If Multiple Target mode has been
enabled, the optional Target Name parameter limits the
list to the maps which satisfy a search for the given target
name. In either mode, the optional LUN parameter limit