Cisco Systems NPE-225 Manual De Usuario

Compiled Wed 02-Feb-05 04:57 by

ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1) 

BOOTLDR: Cisco IOS Software, 7200 Software (C7200-KBOOT-M), 

12.3(20040712:050512) [REL-v123_7_xi_throttle.ios-weekly 115]

Lac1 uptime is 16 hours, 22 minutes 

System returned to ROM by reload at 18:12:49 UTC Mon Feb 7 2005 

System image file is 

"tftp://223.255.254.254/auto/tftpboot-users/biff/c7200-i12s-mz.2005-02-02.BSNOP4_NIGH" 

Last reload reason: Reload command

 

Cisco 7206VXR (NPE-G1) processor (revision 0xFF) with 983040K/65536K bytes of memory. 

Processor board ID 31650243 

SB-1 CPU at 700MHz, Implementation 1025, Rev 0.2, 512KB L2 Cache 

6 slot VXR midplane, Version 2.7

Last reset from power-on 

CPU 1 Multi-Processor Forwarding, Tue Feb 1 00:48:42 PST 2005 [rtang 100]

PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points. 

Current configuration on bus mb1 has a total of 400 bandwidth points. 

This configuration is within the PCI bus capacity and is supported.

PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points. 

Current configuration on bus mb2 has a total of 700 bandwidth points. 

The set of PA-2FE, PA-POS-2OC3, and I/O-2FE qualify for "half 

bandwidth points" consideration, when full bandwidth point counting 

results in oversubscription, under the condition that only one of the 

two ports is used. With this adjustment, current configuration on bus 

mb2 has a total of 700 bandwidth points. 

This configuration has oversubscripted the PCI bus and is not a 

supported configuration.

Please refer to the following document "Cisco 7200 Series Port 

Adaptor Hardware Configuration Guidelines" on CCO <www.cisco.com>, 

for c7200 bandwidth points oversubscription/usage guidelines.

WARNING: PCI bus mb2 Exceeds 600 bandwidth points

1 Ethernet interface 

2 FastEthernet interfaces 

5 Gigabit Ethernet interfaces 

1 ATM interface 

509K bytes of NVRAM.

62976K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes). 

16384K bytes of Flash internal SIMM (Sector size 256K). 

Configuration register is 0x2

 

After installing and cabling the NPE-G1 or NPE-G2 and powering on the router, copy the configuration 
file to the NVRAM on the NPE-G1 or NPE-G2, using one of the following procedures:

If you have kept the previous I/O controller installed in the router, use the procedure given in the 

 to copy 

the saved configuration to the NVRAM on the NPE-G1 or NPE-G2. 

If you have removed the previously installed I/O controller from the router, and you were able to 
copy the file to a CompactFlash Disk, use the procedure given in the 

 to copy the saved 

configuration file to the NVRAM on the NPE-G1 or NPE-G2.

If you have removed the previously installed I/O controller from the router, and you have not been 
able to copy the file to a CompactFlash Disk, use the procedure given in the 

 to copy the saved configuration file to 

the NVRAM on the NPE-G1 or NPE-G2.