SMSC LAN9420 Manual De Usuario
Single-Chip Ethernet Controller with HP Auto-MDIX Support and PCI Interface
Datasheet
SMSC LAN9420/LAN9420i
45
Revision 1.22 (09-25-08)
DATASHEET
Receive Descriptor 3 (RDES3)
3.4.2.2
Transmit descriptors
The descriptors must be 4-DWORD (16-byte) aligned, while there are no alignment restrictions on
transmit buffer addresses. Providing two buffers, two byte-count buffers, and two address pointers in
each descriptor facilitates compatibility with various types of memory-management schemes.
transmit buffer addresses. Providing two buffers, two byte-count buffers, and two address pointers in
each descriptor facilitates compatibility with various types of memory-management schemes.
shows the Transmit Descriptor format.
Table 3.8 RDES3 Bit Fields
BITS
DESCRIPTION
31:0
Buffer 2 Address Pointer (Next Descriptor Address)
The RCH (Second Address Chained) bit (RDES1[24]) determines the usage of this field as
follows:
The RCH (Second Address Chained) bit (RDES1[24]) determines the usage of this field as
follows:
RCH is zero: This field contains the pointer to the address of buffer 2 in Host memory. The buffer
must be DWORD (32-bit) aligned (RDES3[1:0] = 00b). In the case where the buffer is not
DWORD aligned, the resulting behavior is undefined.
must be DWORD (32-bit) aligned (RDES3[1:0] = 00b). In the case where the buffer is not
DWORD aligned, the resulting behavior is undefined.
RCH is one: Descriptor chaining is in use and this field contains the pointer to the next descriptor
in Host memory. The descriptor must be 4-DWORD (16-byte) aligned (RDES3[3:0] = 0000b). In
the case where the buffer is not 4-DWORD aligned, the resulting behavior is undefined.
in Host memory. The descriptor must be 4-DWORD (16-byte) aligned (RDES3[3:0] = 0000b). In
the case where the buffer is not 4-DWORD aligned, the resulting behavior is undefined.
Note:
If RER (RDES1[25]) is set, RCH is ignored and this field is treated as a pointer to buffer
2 as in the “RCH is zero” case above.
2 as in the “RCH is zero” case above.
Host Actions: Initializes this field.
DMAC Actions: Reads this field upon opening a new DMA descriptor to obtain the buffer
address.
DMAC Actions: Reads this field upon opening a new DMA descriptor to obtain the buffer
address.
Figure 3.17 Transmit Descriptor
TDES1
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
TDES2
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
OW
TDES0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
TDES3
BUFFER 1 ADDRESS POINTER
BUFFER 2 ADDRESS POINTER
RESERVED
ES
RES
LC NC LT EC HF
CC
ED UE DE
IC LS FS R
AC TE TC DP R
TBS2
TBS1
CK