Targus APV10US Prospecto

APV10US / 410-0571-001A

Features and specifications subject to change without notice. © 2006, Targus Group International, Inc. and Targus, Inc., Anaheim, CA 92806 USA.

Targus recommends that you register your Targus accessory shortly after purchasing it. To register your Targus accessory, go to: http://www.targus.com/registration.asp
You will need to provide your full name, email address, phone number, and company information (if applicable).
Warranty

Targus warrants this product to be free from defects in materials and workmanship for one years. If your Targus accessory is found to be defective within that time, we will promptly repair or replace 
it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. Under no conditions is Targus liable for loss of, or damage to a computer; nor loss of, or 
damage to, programs, records, or data; nor any consequential or incidental damages, even if Targus has been informed of their possibility. This warranty does not affect your statutory rights. 
Regulatory Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any 
interference received, including interference that may cause undesired operation.
FCC Statement

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not authorized by the party responsible for compliance could void the user’s authority to operate this product
Declaration of Conformity

Hereby, Targus Group International, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Press

air

auto

(DC power only)

For technical questions, please visit:

Internet: www.targus.com/support.asp

Internet: www.targus.com/au

Email: infoaust@targus.com

Telephone: 1800-641-645

Telephone: 0800-633-222

TÜV

Rheinland

Product Safety

This  inverter  is  fitted  with  a  spade  type  32Vdc 
15A fuse.  Once the fuse blows, replace with a 
same  specification  and  type  fuse.  Usage  of 
another  type  fuse  or  metal  wire  will  cause 
abnormal overheating or even fire hazards.

DC In-Auto connector
DC In-Air connector (for airline compatibility, go to Web site below)
http://www.targus.com/

Input: 12-16Vdc
AC Output: 120Vac  60 Hz 
(modified sinewave)  
100W continuous (150W surge)
USB Output: 5Vdc  500mA

Note: When replacing the fuse, please make sure that 

all the electrical device(s) are turned off and the power 

cables are unplugged.  Make sure the fuse is replaced 

correctly and before reconnecting the device(s).

This  listing  is  for  reference  purpose  only.  Some 
devices exceed the wattages listed. Before using the 
device, please refer to the owner’s manual for actual 
wattage required.

Play Station 

 

10 Watt

Cellular Phone Charger 

25 Watt

Portable Color Printer   

30 Watt

Hi-Fi 4 head Stero VCR 

40 Watt

13” color TV 

 

70 Watt

Notebook computer 

 

50 Watt

CD player   

 

85 Watt

Work Light  

 

100 Watt

Problem: Lack of Power Output
Possible causes and suggestions:

• Inverter not adequately warmed up
  Reconnect the cables and make sure the plugs are secure
• Automotive system requires ignition to be “ON” position
  Turn the ignition to “accessory” position
• Battery voltage is below 10 volts
  Recharge or replace the battery
• Equipment being operated draws too much power 
  Reduce load to maximum 100 watts
• Inverter in thermal shut down condition
  Allow the inverter to cool down. Ensure there is ventilation around the 
  unit.

Problem: Low Output Voltage
Possible cause and suggestions:

• Using an average - reading voltmeter
  Use true RMS reading meter
• Inverter is overloaded
  Reduce the load to a maximum 100 watts to maintain regulation
• Input voltage below 10 volts
  Keep input voltage above 10 volts to maintain regulation

WARNINGS
Any electric appliance with the power consump-

tion beyond 100W is not allowed for usage.This 

inverter  is  not  recommended  for  use  with 

inductive  loads,  such  as  fluorescent  lamps  or 

pumps  and  most  heat  generation  equipment 

such as hair dryers, coffee makers, irons, heaters 

and  toasters.  Otherwise,  permanent  damage  to 

the unit and excessive overheating may result.

If  the  external  cable  of  this  inverter  is  damaged,  stop 

using this and contact the authorized agent to replace it to 

avoid hazard.

Regularly  check  input  and  output  connections  are  tight.  

Loose  connections  can  generate  harmful  heat  and  /  or 

damage  the  inverter  or  power  source.    Prevent  shock 

hazard.

This  light  will  flash  (blue  color)  if  the 
inverter encounters problems.

 – Normal operation.

  –  Low  voltage 

warning  signal  indicates  the  supply 
voltage is low.

  –  Unit  is  off  and  no 

power  is  being  output.  Either  the 
inverter is not plugged into a powered 
socket  or  it  has  gone  into  protection 
mode due to overheating, overvoltage, 
overloading or short circuit.

• Do not block or cover any louvered vents . Place 

  the inverter on a flat surface with good ventilation 

  between 0-35 oC and ideally 15-25 oC.  

• Do not place the inverter on or near a heating 

  vent or any piece of heat generating equipment. 

  Keep inverter away from direct sunlight, if at all 

  possible.

• Do not allow water or other liquids to come into 

  contact with the inverter.