Cisco Systems 1000 Series Manual De Usuario

To display the IPv4 neighbor information, use the show ip pim vrf vrf-name neighbor command:

Router# show ip pim vrf blue neighbor

PIM Neighbor Table

Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority,

      P - Proxy Capable, S - State Refresh Capable, G - GenID Capable

Neighbor          Interface                Uptime/Expires    Ver   DR

Address                                                            Prio/Mode

30.2.0.3          Gi0/0/1.3900             2w0d/00:01:37     v2    0 / G

1.1.1.1           Lspvif                   7w0d/00:01:18     v2    1 / B S P G

To display the IPv6 multicast routing table, use the show ipv mroute vrf vrf-name command:

Router# show ipv mroute vrf vrf blue

Multicast Routing Table

Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group,

       C - Connected, L - Local, I - Received Source Specific Host Report,

       P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set,

       J - Join SPT, Y - Joined MDT-data group,

       y - Sending to MDT-data group

       g - BGP signal originated, G - BGP Signal received,

       N - BGP Shared-Tree Prune received, n - BGP C-Mroute suppressed,

       q - BGP Src-Active originated, Q - BGP Src-Active received

       E - Extranet

Timers: Uptime/Expires

Interface state: Interface, State

(2002:30::100, FF33:0:3::4000:1), 00:01:06/00:02:53, flags: sT

  Incoming interface: Lspvif1

  RPF nbr: ::FFFF:1.1.1.2

  Immediate Outgoing interface list:

    GigabitEthernet0/0/1.3900, Forward, 00:01:06/00:02:53

To display the IPv4 multicast routing table, use the show ip mroute vrf-name command:

Router# show ip mroute vrf blue

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,

       L - Local, P - Pruned, R - RP-bit set, F - Register flag,

       T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,

       X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,

       U - URD, I - Received Source Specific Host Report,

       Z - Multicast Tunnel, z - MDT-data group sender,

       Y - Joined MDT-data group, y - Sending to MDT-data group,

       G - Received BGP C-Mroute, g - Sent BGP C-Mroute,

       N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,

       Q - Received BGP S-A Route, q - Sent BGP S-A Route,

       V - RD & Vector, v - Vector, p - PIM Joins on route,

       x - VxLAN group

Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join

 Timers: Uptime/Expires

 Interface state: Interface, Next-Hop or VCD, State/Mode

(30.0.0.100, 232.0.0.1), 1w0d/00:01:47, flags: sT

  Incoming interface: Null, RPF nbr 1.1.1.1

  Outgoing interface list:

    Gi0/0/1.3900, Forward/Sparse, 1w0d/00:01:47