Cisco Systems 1000 Series Manual De Usuario
5-20
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
OL-16506-17
Chapter 5 Software Upgrade Processes Supported by Cisco ASR 1000 Series Routers
ISSU Upgrade for Redundant Platforms
Step 10
issu loadversion rp
standby-RP
file
target-standbyRP-URL-for-sub-packages
:asr1000rp*
version
*.pkg
force
Example:
Router# issu loadversion rp 1 file
stby-bootflash:asr1000rp*03.13.00.S.154-3.S-ext
*.pkg force
Upgrade the RP subpackages on the standby RP, where the
“rp*” wildcard is specified to capture all of the RP
subpackages for the desired upgrade release.
“rp*” wildcard is specified to capture all of the RP
subpackages for the desired upgrade release.
Step 11
hw-module slot
standby-RP
reload
Example:
Router# hw-module slot R1 reload
Reload the standby RP.
Step 12
issu loadversion rp
active-RP
file
URL-to-active-file-system
:asr1000rp2-{sipbase,sip
spa}*
version
*.pkg slot
SIP-slot-number
force
issu commitversion
Example:
Router# issu loadversion rp 0 file
bootflash:asr1000rp2-{sipbase,sipspa}*03.13.00.
S.154-3.S-ext*.pkg slot 0 force
Upgrade the SIP and SPA subpackages for each SIP on the
router.
router.
Note
This step must be completed one SIP at a time, and
repeated for each SIP installed on the router before
performing the next step.
repeated for each SIP installed on the router before
performing the next step.
Tip
You can use the show ip interface brief command
to identify which slots contain SIPs and SPAs. The
interfaces with three numbers (in the form
SIP-number/SPA-number/interface-number)
identify the SIP and SPA locations in the router.
to identify which slots contain SIPs and SPAs. The
interfaces with three numbers (in the form
SIP-number/SPA-number/interface-number)
identify the SIP and SPA locations in the router.
Note
The pattern options used in this CLI (sipbase and
sipspa) were introduced in Cisco IOS XE Release
2.1.2 and are not available in previous Cisco IOS
XE Releases.
See the
sipspa) were introduced in Cisco IOS XE Release
2.1.2 and are not available in previous Cisco IOS
XE Releases.
See the
for pre-Cisco
IOS XE Release 2.1.2 ISSU upgrade procedures.
Step 13
issu loadversion rp
active-RP
file
URL-to-active-file-system
:asr1000rp2-{elcbase,elc
spa}*
version
*.pkg slot
SIP-slot-number
force
issu commitversion
Repeat this step for each ELC installed in the
router before moving onto the next step.
Example:
Router# issu loadversion rp 0 file
bootflash:asr1000rp2-{elcbase,elcspa}*03.13.00.
S.154-3.S-ext*.pkg slot 0 force
Upgrade the ELC and SPA subpackages for each ELC on
the router.
the router.
Note
This step must be completed for one ELC at a time,
and repeated for each ELC installed on the router
before performing the next step.
and repeated for each ELC installed on the router
before performing the next step.
Tip
You can use the show ip interface brief command
to identify which slots contain ELCs and SPAs. The
interfaces with three numbers (in the form
ELC-number/SPA-number/interface-number)
identify the ELC and SPA locations in the router.
to identify which slots contain ELCs and SPAs. The
interfaces with three numbers (in the form
ELC-number/SPA-number/interface-number)
identify the ELC and SPA locations in the router.
Note
The pattern options used in this CLI (elcbase and
elcspa) were introduced in Cisco IOS XE Release
3.10S and are not available in previous Cisco IOS
XE Releases.
elcspa) were introduced in Cisco IOS XE Release
3.10S and are not available in previous Cisco IOS
XE Releases.
Command or Action
Purpose