Toshiba TDP-TW420 Manual De Usuario
18
19
Preparations
Names of the terminals on the rear panel
(12)
(11)
(8)
(7)
(5)
(6)
(4)
(3)
(1) (2)
(9) (10)
Name
: Main Function
(1)
LAN terminal
: Connects a network cable.
(2)
USB terminal
: Connects a commercial USB memory.
p.46
(3)
COMPUTER (Y/P
B
/P
R
) 2 IN terminal
: Input analog RGB signal from a computer or other
source, or a component video signal (Y/P
B
/P
R
) from video
equipment.
AUDIO IN: Input audio signals.
(4)
COMPUTER (Y/P
B
/P
R
) 1 IN terminal
: Input analog or digital RGB signal from a computer, or a
component video signal (Y/P
B
/P
R
) from video equipment.
AUDIO IN: Input audio signals.
(5)
VIDEO terminal
: Input video signals from video equipment.
(6)
AC IN socket
: Connects the supplied power cord here.
(7)
CONTROL terminal
: When operating the projector via a computer, connect this
to the controlling computer’s RS-232C port.
p.100
(8)
Main power switch
: AC power line ON (standby)/OFF.
(9)
MONITOR terminal
: Connect to a computer display, etc.
(10)
AUDIO OUT terminal
: Outputs audio signals.
(11)
AUDIO (L/R) terminal
: Input audio signals from video equipment. (Dual use for
VIDEO and S-VIDEO)
(12)
S-VIDEO terminal
: Input S video signals from video equipment.
Loading dry-cell batteries
into the remote control
into the remote control
1
Remove the battery cover.
2
Insert the dry-cell batteries.
Be sure to align the plus and minus ends
of the batteries properly.
of the batteries properly.
Two batteries (LR03, SIZE AAA) are used.
3
Replace the battery cover.
■
Operating the remote
control
control
Point toward the projector’s infrared
remote sensor, and press any button
on the remote control.
remote sensor, and press any button
on the remote control.
Operating the projector from the front
Approx.15°
Appro
x.5m
When operating the remote control
from behind the projector, infrared
signal is refl ected on the projecting
surface and may travel a shorter
distance to reach the projector
depending on the shape and material
of the projecting surface.
from behind the projector, infrared
signal is refl ected on the projecting
surface and may travel a shorter
distance to reach the projector
depending on the shape and material
of the projecting surface.
■
•
Dry-cell batteries
Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
Remove batteries from remote control when not using for extended periods.
If the remote control stops working, or if its range decreases, replace all the batteries
with new ones.
Keep the batteries away from the reach of children.
Batteries are choking hazards and can be very dangerous if swallowed. If the batteries
are swallowed, seek medical assistance immediately.
previous pages.
Remove batteries from remote control when not using for extended periods.
If the remote control stops working, or if its range decreases, replace all the batteries
with new ones.
Keep the batteries away from the reach of children.
Batteries are choking hazards and can be very dangerous if swallowed. If the batteries
are swallowed, seek medical assistance immediately.
The remote control
The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fl uorescent lighting.
Do not drop or bang.
Do not leave in hot or humid locations.
Do not allow it to get wet or place it on top of wet objects.
Do not take apart.
In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
sunlight or fl uorescent lighting.
Do not drop or bang.
Do not leave in hot or humid locations.
Do not allow it to get wet or place it on top of wet objects.
Do not take apart.
In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Preparing and using the remote control