Toshiba TDP-TW420 Manual De Usuario
26
27
Operations
Basic operations
1
Turn on the power.
Turn on the power by following the instructions in “Turning the power on”
p.24
.
2
Select the language and the lamp power (When using the
fi rst time).
When the projector is used for the fi rst time after purchase, the start menu for language
(to display the menus and messages on the screen) and lamp power selection and
confi guration is displayed in English. (If the screen is out of focus, adjust it according to
the step
(to display the menus and messages on the screen) and lamp power selection and
confi guration is displayed in English. (If the screen is out of focus, adjust it according to
the step
6
.)
1
Use the
,
,
or
button to select the desired language and
press the
button.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Polish
Norwegian
Finnish
Czech
Hungarian
Greek
Danish
Dutch
Rumanian
Norwegian
Finnish
Czech
Hungarian
Greek
Danish
Dutch
Rumanian
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Indonesian
Chinese (simplified)
Chinese (traditional)
Korean
Indonesian
Message for setup confi rmation is displayed in a selected language.
Then, the menu for lamp power selection and confi guration is displayed. It is
automatically set as Standard. To change the setting, follow the step
Then, the menu for lamp power selection and confi guration is displayed. It is
automatically set as Standard. To change the setting, follow the step
2
.
2
Use the
or
button to select the lamp power and press the
button.
The lamp power, if selected, will be toggled without pressing the
button. The display
automatically disappears in a few seconds.
Notes
When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting 2 menu
startup. However, if [Reset all] is executed from the Default setting 2 menu
p.42
,
the start menu will be displayed the next time when the power is turned on.
The language can also be set via the Display setting menu
The language can also be set via the Display setting menu
p.38
and Lamp power
via the Default setting 2 menu
p.42
.
This owner’s manual assumes that English has been selected.
3
Activate the connected device.
Turn on and start the connected device such as a computer.
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
•
•
•
Notes
When [Auto input search] is set to [Off] in the Default setting 1 menu
p.41
(factory setting is [On]), the Input select menu appears if you press the INPUT
button.
If no signal is being output from the connected equipment, pressing the INPUT
button does not change the input and “There is no other input signal.” message
will appear.
button.
If no signal is being output from the connected equipment, pressing the INPUT
button does not change the input and “There is no other input signal.” message
will appear.
5
Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the
foot adjuster.
foot adjuster.
1
Lift up the front of the projector to
the desired angle, then press the foot
adjuster release button.
adjuster release button.
The foot adjuster extends. Release the button
to lock the position.
to lock the position.
2
To fi ne adjust the angle, twist the foot
adjuster.
3
To adjust the horizontal angle, use the
right and left tilt adjusters.
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
release button, then slowly lower the projector.
Note
When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone
distortion will automatically be corrected based on the projector placement angle. If
you do not desire the automatic keystone correction, set [Auto keystone] to [Off].
6
Adjusting the screen size and focus
1
Use the zooming ring to adjust the
screen size.
2
Use the focusing ring to adjust the
focus.
7
Adjusting the volume with the
buttons
The speaker volume can be adjusted when an audio signal is being input.
•
•
•
•
Zooming ring
Focusing ring
2
1