Samsung SCX-5935 Series Manual De Usuario

Media and tray_ 49

•

Place them on a flat surface after removing them from the machine.

•

Do not leave unused transparencies in the paper tray for long periods of 

time. Dust and dirt may accumulate on them, resulting in spotty printing.

•

To avoid smudging caused by fingerprints, handle them carefully.

•

To avoid fading, do not expose printed transparencies to prolonged 

sunlight.

•

Ensure that transparencies are not wrinkled, curled, or have any torn 

edges.

•

Do not use transparencies that separates from the backing sheet.

•

To prevent transparencies from sticking to each other, do not let the 

printed sheets stack up as they are begin printed out. 

•

Recommended media: Transparency for a color laser printer by Xerox, 

such as 3R 91331(A4), 3R 2780(Letter)

To avoid damaging the machine, use only labels designed for use in laser 

machines.

•

When selecting labels, consider the following factors:

-

Adhesives :  The adhesive material should be stable at your 

machine’s fusing temperature. Check your machine’s specification to 

view the fusing temperature. (See "General specifications" on 

page 127.)

-

Arrangement :  Only use labels with no exposed backing between 

them. Labels can peel off sheets that have spaces between the 

labels, causing serious jams.

-

Curl :  Prior to printing, labels must lie flat with no more than 13 mm 

of curl in any direction.

-

Condition :  Do not use labels with wrinkles, bubbles, or other 

indications of separation.

•

Make sure that there is no exposed adhesive material between labels. 

Exposed areas can cause labels to peel off during printing, which can 

cause paper jams. Exposed adhesive can also cause damage to 

machine components.

•

Do not run a sheet of labels through the machine more than once. The 

adhesive backing is designed for only a single pass through the 

machine.

•

Do not use labels that are separating from the backing sheet or are 

wrinkled, bubbled, or otherwise damaged.

•

Do not print on media smaller than 76.2 mm (3 inches) wide or 127 mm 

(4 inches) long.

•

In the software application, set margins at least 6.4 mm (0.25 inches) 

away from the edges of the material.

When loading preprinted paper, printed side should be facing down with an 

uncurled edge at the front. If you experience problems with paper feed, turn 

the paper around. Note that print quality is not guaranteed.

•

Preprinted paper must be printed with heat-resistant ink that will not 

melt, vaporize, or release hazardous emissions when subjected to the 

machine’s fusing temperature for 0.1 second. Check your machine’s 

specification to view the fusing temperature. (See "General 

•

Preprinted paper ink must be non-flammable and should not adversely 

affect machine rollers.

•

Before you load preprinted paper, verify that the ink on the paper is dry. 

During the fusing process, wet ink can come off preprinted paper, 

reducing print quality.

•

Make sure not to use the inkjet photo paper with this machine. It could 

cause damage to the machine. 

Load one paper to the multi-purpose tray at a time, glossy side facing 

up. 

•

Recommended media: Glossy paper (Letter) for this machine by HP 

Brochure Paper (Product: Q6611A) only.

•

Recommended media: Glossy paper (A4) for this machine by HP 

Superior Paper 160 glossy (Product: Q6616A).

After loading paper in the paper tray, set the paper size and type using the 

control panel. These settings will apply to copy and fax modes. For 

computer printing, select the paper size and type in the application program 

you use on your computer. (See "Paper tab" on page 55.)

The settings made from the machine driver override the settings on 

the control panel.

1. Press Machine Setup on the control panel.
2. Press Admin Setting.
3. When the login message appears, enter password with number keypad 

and press OK. (See "Setting the authentication password" on page 41.)

4. Press the General tab.
5. Press the down arrow to switch the screen, press Tray Management.