Cisco Systems 3560 Manual De Usuario
36-67
Catalyst 3560 Switch Software Configuration Guide
OL-8553-06
Chapter 36 Configuring IP Unicast Routing
Configuring ISO CLNS Routing
Step 9
set-overload-bit [on-startup
{seconds | wait-for-bgp}]
{seconds | wait-for-bgp}]
(Optional) Set an overload bit (a hippity bit) to allow other routers to ignore
the router in their shortest path first (SPF) calculations if the router is
having problems.
the router in their shortest path first (SPF) calculations if the router is
having problems.
•
(Optional) on-startup—sets the overload bit only on startup. If
on-startup is not specified, the overload bit is set immediately and
remains set until you enter the no set-overload-bit command. If
on-startup is specified, you must enter a number of seconds or
wait-for-bgp.
on-startup is not specified, the overload bit is set immediately and
remains set until you enter the no set-overload-bit command. If
on-startup is specified, you must enter a number of seconds or
wait-for-bgp.
•
seconds—When the on-startup keyword is configured, causes the
overload bit to be set upon system startup and remain set for this
number of seconds. The range is from 5 to 86400 seconds.
overload bit to be set upon system startup and remain set for this
number of seconds. The range is from 5 to 86400 seconds.
•
wait-for-bgp—When the on-startup keyword is configured, causes
the overload bit to be set upon system startup and remain set until BGP
has converged. If BGP does not signal IS-IS that it is converged, IS-IS
will turn off the overload bit after 10 minutes.
the overload bit to be set upon system startup and remain set until BGP
has converged. If BGP does not signal IS-IS that it is converged, IS-IS
will turn off the overload bit after 10 minutes.
Step 10
lsp-refresh-interval seconds
(Optional) Set an LSP refresh interval in seconds. The range is from 1 to
65535 seconds. The default is to send LSP refreshes every 900 seconds
(15 minutes).
65535 seconds. The default is to send LSP refreshes every 900 seconds
(15 minutes).
Step 11
max-lsp-lifetime seconds
(Optional) Set the maximum time that LSP packets remain in the router
database without being refreshed. The range is from 1 to 65535 seconds.
The default is 1200 seconds (20 minutes). After the specified time interval,
the LSP packet is deleted.
database without being refreshed. The range is from 1 to 65535 seconds.
The default is 1200 seconds (20 minutes). After the specified time interval,
the LSP packet is deleted.
Step 12
lsp-gen-interval [level-1 | level-2]
lsp-max-wait [lsp-initial-wait
lsp-second-wait]
lsp-max-wait [lsp-initial-wait
lsp-second-wait]
(Optional) Set the IS-IS LSP generation throttling timers:
•
lsp-max-wait—the maximum interval (in seconds) between two
consecutive occurrences of an LSP being generated. The range is 1 to
120, the default is 5.
consecutive occurrences of an LSP being generated. The range is 1 to
120, the default is 5.
•
lsp-initial-wait—the initial LSP generation delay (in milliseconds).
The range is 1 to 10000; the default is 50.
The range is 1 to 10000; the default is 50.
•
lsp-second-wait—the hold time between the first and second LSP
generation (in milliseconds). The range is 1 to 10000; the default is
5000.
generation (in milliseconds). The range is 1 to 10000; the default is
5000.
Step 13
spf-interval [level-1 | level-2]
spf-max-wait [spf-initial-wait
spf-second-wait]
spf-max-wait [spf-initial-wait
spf-second-wait]
(Optional) Sets IS-IS shortest path first (SPF) throttling timers.
•
spf-max-wait—the maximum interval between consecutive SFPs (in
seconds). The range is 1 to 120, the default is 10.
seconds). The range is 1 to 120, the default is 10.
•
spf-initial-wait—the initial SFP calculation after a topology change (in
milliseconds). The range is 1 to 10000; the default is 5500.
milliseconds). The range is 1 to 10000; the default is 5500.
•
spf-second-wait—the holdtime between the first and second SFP
calculation (in milliseconds). The range is 1 to 10000; the default is
5500.
calculation (in milliseconds). The range is 1 to 10000; the default is
5500.
Command
Purpose