Cisco Systems 3560X Manual De Usuario
5-4
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-21521-01
Chapter 5 Managing Switch Stacks
Understanding Switch Stacks
–
–
–
Note
A switch stack is different from a switch cluster. A switch cluster is a set of switches connected through
their LAN ports, such as the 10/100/1000 ports. For more information about how switch stacks differ
from switch clusters, see the “Planning and Creating Clusters” chapter in the Getting Started with Cisco
Network Assistant
their LAN ports, such as the 10/100/1000 ports. For more information about how switch stacks differ
from switch clusters, see the “Planning and Creating Clusters” chapter in the Getting Started with Cisco
Network Assistant
on Cisco.com.
Switch Stack Membership
A switch stack has up to nine stack members connected through their StackWise Plus ports. A switch
stack always has one stack master.
stack always has one stack master.
A standalone switch is a switch stack with one stack member that also operates as the stack master. You
can connect one standalone switch to another (
can connect one standalone switch to another (
) to create a switch stack
containing two stack members, with one of them as the stack master. You can connect standalone
switches to an existing switch stack (
switches to an existing switch stack (
) to increase the stack membership.
If you replace a stack member with an identical model, the new switch functions with exactly the same
configuration as the replaced switch, assuming that the new switch is using the same member number as
the replaced switch. For information about the benefits of provisioning a switch stack, see the
configuration as the replaced switch, assuming that the new switch is using the same member number as
the replaced switch. For information about the benefits of provisioning a switch stack, see the
. For information about replacing a failed switch, see
the “Troubleshooting” chapter in the hardware installation guide.
The operation of the switch stack continues uninterrupted during membership changes unless you
remove the stack master or you add powered-on standalone switches or switch stacks.
remove the stack master or you add powered-on standalone switches or switch stacks.
Note
Make sure that you power off the switches that you add to or remove from the switch stack.
After adding or removing stack members, make sure that the switch stack is operating at full bandwidth
(64 Gb/s). Press the Mode button on a stack member until the Stack mode LED is on. The last two right
port LEDs on all switches in the stack should be green. Depending on the switch model, the last two
right ports are 10-Gigabit Ethernet ports or small form-factor pluggable (SFP) module ports
(10/100/1000 ports). If one or both of these LEDs are not green on any of the switches, the stack is not
operating at full bandwidth.
(64 Gb/s). Press the Mode button on a stack member until the Stack mode LED is on. The last two right
port LEDs on all switches in the stack should be green. Depending on the switch model, the last two
right ports are 10-Gigabit Ethernet ports or small form-factor pluggable (SFP) module ports
(10/100/1000 ports). If one or both of these LEDs are not green on any of the switches, the stack is not
operating at full bandwidth.
•
Adding powered-on switches (merging) causes the stack masters of the merging switch stacks to
elect a stack master from among themselves. The re-elected stack master retains its role and
configuration and so do its stack members. All remaining switches, including the former stack
masters, reload and join the switch stack as stack members. They change their stack member
numbers to the lowest available numbers and use the stack configuration of the re-elected stack
master.
elect a stack master from among themselves. The re-elected stack master retains its role and
configuration and so do its stack members. All remaining switches, including the former stack
masters, reload and join the switch stack as stack members. They change their stack member
numbers to the lowest available numbers and use the stack configuration of the re-elected stack
master.
•
Removing powered-on stack members causes the switch stack to divide (partition) into two or more
switch stacks, each with the same configuration. This can cause an IP address configuration conflict
in your network. If you want the switch stacks to remain separate, change the IP address or addresses
of the newly created switch stacks. If you did not intend to partition the switch stack:
switch stacks, each with the same configuration. This can cause an IP address configuration conflict
in your network. If you want the switch stacks to remain separate, change the IP address or addresses
of the newly created switch stacks. If you did not intend to partition the switch stack:
a.
Power off the switches in the newly created switch stacks.
b.
Reconnect them to the original switch stack through their StackWise Plus ports.
c.
Power on the switches.