Cisco Systems 3560X Manual De Usuario
39-2
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-21521-01
Chapter 39 Configuring QoS
Understanding QoS
Understanding QoS
Typically, networks operate on a best-effort delivery basis, which means that all traffic has equal priority
and an equal chance of being delivered in a timely manner. When congestion occurs, all traffic has an
equal chance of being dropped.
and an equal chance of being delivered in a timely manner. When congestion occurs, all traffic has an
equal chance of being dropped.
When you configure the QoS feature, you can select specific network traffic, prioritize it according to
its relative importance, and use congestion-management and congestion-avoidance techniques to
provide preferential treatment. Implementing QoS in your network makes network performance more
predictable and bandwidth utilization more effective.
its relative importance, and use congestion-management and congestion-avoidance techniques to
provide preferential treatment. Implementing QoS in your network makes network performance more
predictable and bandwidth utilization more effective.
The QoS implementation is based on the Differentiated Services (Diff-Serv) architecture, an emerging
standard from the Internet Engineering Task Force (IETF). This architecture specifies that each packet
is classified upon entry into the network.
standard from the Internet Engineering Task Force (IETF). This architecture specifies that each packet
is classified upon entry into the network.
The classification is carried in the IP packet header, using 6 bits from the deprecated IP type of service
(ToS) field to carry the classification (class) information. Classification can also be carried in the
Layer 2 frame. These special bits in the Layer 2 frame or a Layer 3 packet are described here and shown
in
(ToS) field to carry the classification (class) information. Classification can also be carried in the
Layer 2 frame. These special bits in the Layer 2 frame or a Layer 3 packet are described here and shown
in
:
•
Prioritization bits in Layer 2 frames:
Layer 2 Inter-Switch Link (ISL) frame headers have a 1-byte User field that carries an IEEE 802.1p
class of service (CoS) value in the three least-significant bits. On ports configured as Layer 2 ISL
trunks, all traffic is in ISL frames.
class of service (CoS) value in the three least-significant bits. On ports configured as Layer 2 ISL
trunks, all traffic is in ISL frames.
Layer 2 802.1Q frame headers have a 2-byte Tag Control Information field that carries the CoS value
in the three most-significant bits, which are called the User Priority bits. On ports configured as
Layer 2 802.1Q trunks, all traffic is in 802.1Q frames except for traffic in the native VLAN.
in the three most-significant bits, which are called the User Priority bits. On ports configured as
Layer 2 802.1Q trunks, all traffic is in 802.1Q frames except for traffic in the native VLAN.
Other frame types cannot carry Layer 2 CoS values.
Layer 2 CoS values range from 0 for low priority to 7 for high priority.
•
Prioritization bits in Layer 3 packets:
Layer 3 IP packets can carry either an IP precedence value or a Differentiated Services Code Point
(DSCP) value. QoS supports the use of either value because DSCP values are backward-compatible
with IP precedence values.
(DSCP) value. QoS supports the use of either value because DSCP values are backward-compatible
with IP precedence values.
IP precedence values range from 0 to 7.
DSCP values range from 0 to 63.
Note
You can use the dual IPv4 and IPv6 SDM templates and enable IPv6 QoS globally on the switch or
switch stack. You must reload the switch after configuring the dual IPv4 and IPv6 templates. For more
information, see
switch stack. You must reload the switch after configuring the dual IPv4 and IPv6 templates. For more
information, see
running the LAN base feature set.