Emerson 5150 Manual De Usuario

1-1     Installation 

Connectivity Module 

 

 

 

The Connectivity Module (CM) mounts on a DIN rail 
under the ATS Controller (Group 5 & 1). A short serial 
cable connects the CM to the Controller. If a Power 
Manager (PM) or Digital Power Meter (DPM) is present, 
a long serial cable connects the CM to the PM.  Refer to 
installation drawings provided and follow the steps below 
to install the Connectivity Module. 

 

K889950 

for 7000 & 4000 Series 

and Series 300 only 

K889950-001 for 

7000 & 4000 Series 

and Series 300 

with PM or DPM 

Connectivity 
Module 5150 

629800-004 

Connectivity 
Module 5150 

629800-004 

DIN Rail and 
Hardware 

754607 

DIN Rail and 
Hardware 

754607 

10-in. Serial 
Cable for 
Controller 

629798-001 

10-in. Serial 
Cable for 
Controller 

629798-001 

  4-ft 

Serial 

Cable for  
PM or DPM * 

629798-002 

 

* A 9-foot serial cable (629798-004) is 

required for G7ATB, G7ACTB, G7ADTB. 

1.  De-energize both Normal and Emergency sources 

that feed the ATS. Open enclosure door and check 
with a non-contact AC voltage detector. 

 

2.  Mount the DIN rail (supplied in the kit) onto two 

studs (on the door) below the Controller. 

 

Connectivity Module will mount on the right side.  

 

3.  Install Connectivity Module onto DIN rail by 

hooking the bottom of module on bottom of DIN rail 
and rocking it upward unit it snaps in place.  

 

4.  Install the 10-inch serial cable between the Controller 

receptacle (J7 on Group 5, J4 on Group 1) and the 
Connectivity Module J1 receptacle.  

 

5.  If a PM (or DPM) is present, connect the 4-foot serial 

cable between the PM J5 receptacle (or DPM J2 
receptacle) and the Connectivity Module J2 
receptacle.*  

 

Now test communications (go to page 1-2). 

 

 

The Connectivity Module (CM) mounts on a DIN rail 
near the ATS Control Panel. A separate power supply is 
needed unless it is connected to a Power Manager (PM). 
Group 6A/7A Control Panel must have a Serial 
Communication Kit added. A single communication 
cable (2 twisted pairs and overall shield connects the CM 
to the Control Panel). Refer to installation drawings 
provided and follow the steps below to install the 
Connectivity Module. 

 

K889953 

for ASCO 940/962 only

 

K889953-001 

for ASCO 940/962 with PM

 

Connectivity 
Module 5150 

629800-004 

Connectivity 
Module 5150 

629800-004 

DIN Rail and 
Hardware 

754610 

DIN Rail and 
Hardware 

754610 

Serial Com. 
Kit for Group 
6A/7A CP * 

467508 

Serial Com. 
Kit for Group 
6A/7A CP * 

467508 

  Serial 

Cable 

for PM 

629798-002 

* Serial communication & transient protection boards. 

 

Power Supply ** 

not supplied

 

(4 wires and an overall shield) 

not supplied

 

24 Vdc, 80 mA ** use 

16 AWG wire 

Belden 9842, 9829, 89729, 82729 or 

Alpha 6202C, 6222C, 58902 only 

 
** If a Power Manager (PM) is present, a power supply is not needed for 
the Connectivity Module (CM). The serial cable from the PM provides 
the power to the CM. 
 
 
 
 

1.  De-energize both Normal and Emergency sources 

that feed the ATS. Open enclosure door and check 
with a non-contact AC voltage detector. 

 

2.  Mount DIN rail (supplied in the kit) onto two studs 

(on the door) below or adjacent to the Control Panel.  

 

3.  Install the Connectivity Module onto DIN rail. 

 

4.  Prepare and connect the specified communication 

cable between the Control Panel terminals and the 
Connectivity Module J4 terminals as listed below: 

 

5.  Prepare and connect the 24 Vdc power supply to the 

Connectivity Module. Use 16 AWG wiring to J5 
terminal plug (1 is + positive, 2 is – negative).  

 

Now test communications (go to page 1-2).